Eigenschaften
Allgemein
| Property | Value | Comment | |
|---|---|---|---|
Carbon equivalent (CET) | 0.29 [-] Show Supplier Material materials with Carbon equivalent (CET) of 0.29 [-] | for thickness 4-15 mm | |
0.3 [-] Show Supplier Material materials with Carbon equivalent (CET) of 0.3 [-] | for thickness 15.01-40 mm | ||
0.33 [-] Show Supplier Material materials with Carbon equivalent (CET) of 0.33 [-] | for thickness 40.01-64 mm | ||
Carbon equivalent (CEV) | 0.44 [-] Show Supplier Material materials with Carbon equivalent (CEV) of 0.44 [-] | for thickness 15.01-25 mm | |
0.45 [-] Show Supplier Material materials with Carbon equivalent (CEV) of 0.45 [-] | for thickness 4-15 mm | ||
0.45 [-] Show Supplier Material materials with Carbon equivalent (CEV) of 0.45 [-] | for thickness 25.01-40 mm | ||
0.54 [-] Show Supplier Material materials with Carbon equivalent (CEV) of 0.54 [-] | for thickness 40.01-64 mm | ||
Carbon equivalent note | CEV = C+Mn/6+ (Ni+Cu)/15+ (Cr+Mo+V)/5 and CET = C+(Mn+Mo)/10+Ni/40 +(Cr+Cu)/20 | ||
Abmessung
| Property | Value |
|---|---|
Breite | 1500 - 3100 mm Show Supplier Material materials with Breite of 1500 - 3100 mm |
Mechanisch
| Property | Temperature | Value | Comment |
|---|---|---|---|
Charpy impact energy, V-notch | -40 °C | 27 J Show Supplier Material materials with Charpy impact energy, V-notch of 27 J | Transverse testing | thickness < 12 mm | Option 30 according to EN 10025 |
-20 °C | 30 J Show Supplier Material materials with Charpy impact energy, V-notch of 30 J | Transverse testing | thickness < 12 mm | Option 30 according to EN 10025 | |
0 °C | 35 J Show Supplier Material materials with Charpy impact energy, V-notch of 35 J | Transverse testing | thickness < 12 mm | Option 30 according to EN 10025 | |
Dehnung | 14 % Show Supplier Material materials with Dehnung of 14 % | min. | A5 | Transverse | |
Streckgrenze | 700 MPa Show Supplier Material materials with Streckgrenze of 700 MPa | min. | Transverse | |
Zugfestigkeit | 780 - 930 MPa Show Supplier Material materials with Zugfestigkeit of 780 - 930 MPa | Transverse |
Chemical properties
| Property | Value | Comment |
|---|---|---|
Aluminium | 0.07 % Show Supplier Material materials with Aluminium of 0.07 % | max. |
Bor | 0.005 % Show Supplier Material materials with Bor of 0.005 % | max. |
Chrom | 0.8 % Show Supplier Material materials with Chrom of 0.8 % | max. |
Kohlenstoff | 0.2 % Show Supplier Material materials with Kohlenstoff of 0.2 % | max. |
Mangan | 1.5 % Show Supplier Material materials with Mangan of 1.5 % | max. |
Molybdän | 0.5 % Show Supplier Material materials with Molybdän of 0.5 % | max. |
Nickel | 1 % Show Supplier Material materials with Nickel of 1 % | max. |
Niobium | 0.04 % Show Supplier Material materials with Niobium of 0.04 % | max. |
Phosphor | 0.02 % Show Supplier Material materials with Phosphor of 0.02 % | max. |
Schwefel | 0.01 % Show Supplier Material materials with Schwefel of 0.01 % | max. |
Silizium | 0.6 % Show Supplier Material materials with Silizium of 0.6 % | max. |
Stickstoff | 0.014 % Show Supplier Material materials with Stickstoff of 0.014 % | max. |
Titan | 0.04 % Show Supplier Material materials with Titan of 0.04 % | max. |
Vanadium | 0.07 % Show Supplier Material materials with Vanadium of 0.07 % | max. |
Technological properties
| Property | ||
|---|---|---|
| Application areas | Quend 700 is recommended for the following applications: | |
| Chemical composition | The steel is fine grain treated. | |
| Cold Forming | Quend 700 is very well suited for cold forming operations. Quend 700 complies with the S690QL bending requirements but offer even closer R/t ratios: *R = Recommended punch radius (mm), t = Plate thickness (mm) , W – Die opening width (mm) (bending angle ≤ 90°) Due to the homogeneous properties and narrow thickness tolerances of Quend 700, variations in springback are kept at a low level. Grinding of flame cut or a sheared edge in the bending area is recommended to further prevent cracking during bending. | |
| Delivery condtion | Quend 700 is delivered as quenched and tempered. Our Quend plates are supplied as standard in the shotblasted and painted condition. In order to maintain a good weldability and laser cutting performance, a low zinc silicate primer is applied. Plates can also be delivered unpainted. | |
| Heat Treatment | The mechanical properties of Quend 700 has been obtained by quenching and tempering. For not losing the guaranteed properties of Quend 700, the plate should not be used in applications requiring hot working and service temperatures above 550 °C. | |
| Machining | Quend 700 provides a very good machinability and can be drilled, counter sinked and milled in the same way as any other 700MPa or S690QL Q&T steel. | |
| Other | Quend 700 is delivered with a unique combination of excellent flatness, tight thickness tolerances and superior surface finish. | |
| Testings | Ultra sonic testing (UT), is applied to secure the plate from discontinuities like inclusions, cracks and porosity. In thickness from 8 mm and up, all plates are UT tested and controlled against class S2, E2, according to EN 10160. | |
| Thermal cutting and welding | Quend 700 may be cut either by oxygen fuel, plasma and laser cutting without any restrictions. Subsequent to cutting, let the cut parts slowly cool down to room temperature. Do never accelerate the cooling of the parts. A slow cooling rate will reduce the risk of cut edge cracking. | |
| Welding | Welding of Quend 700 can be performed using any of the conventional welding methods available both as manual or automatic. In the thickness range up to 30 mm, preheating prior to welding is normally not needed, if a heat input of 1,7 kJ/mm is used. Welding of Quend 700 is recommended to be performed at ambient temperature not lower than +5 °C. Subsequent to welding, let the welded parts slowly cool down to room temperature. Do never accelerate the cooling process of the weld. It is always recommended to use low hydrogen electrodes when welding Quend 700. | |