DC04 AM FCE

Nombres alternativos y comerciales
Solstamp 04

Want to keep this datasheet? Save it now in your required format

Description

DC04 AM FCE is a cold rolled non-alloyed mild steel grades with guaranteed maximum yield and tensile strength, guaranteed minimum ductility (elongation at fracture) and good formability (n and r values). These grades comply with the requirements of the EN 10130:2006 standard and are obtained after either batch or continuous annealing. This steel grade has excellent formability, which facilitates cold forming operations, and are ideal for deep drawing. This steel for cold forming also offer excellent forming performance, due to the low scattering of their chemical composition and their mechanical properties, which guarantees processing consistency.

Related Standards

Equivalent Materials

Los datos sobre este material han sido proporcionados por ArcelorMittal.

A menos que se indique lo contrario, todas las medidas corresponden a condiciones de temperatura ambiente. A menos que se indique lo contrario, se utilizan las unidades del SI.
Las normas armonizadas son similares a uno o varios estándares del proveedor. Es posible que algunas normas armonizadas se ajusten al estándar original, mientras que otras pueden quedar fuera de su alcance.

Ashby charts

All categories

Propiedades

General

Property	Value	Comment
Mean Roughness	0.6 - 1.9 μm Show Supplier Material materials with Mean Roughness of 0.6 - 1.9 μm	wide range of roughness levels according to the EN 10130 standard can be supplied upon request.

Medidas

Property	Value
Dimensions	Please feel free to check the figure on the right side of the material page for more details.

Mecánica

Property	Value	Comment
Elongación	34 % Show Supplier Material materials with Elongación of 34 %	min. \| for thickness 0.3-0.5 mm \| Transverse \| A80
	36 % Show Supplier Material materials with Elongación of 36 %	min. \| for thickness 0.5-0.7 mm \| Transverse \| A80
	38 % Show Supplier Material materials with Elongación of 38 %	min. \| for thickness 0.7-3 mm \| Transverse \| A80
Límite elástico	140 - 250 MPa Show Supplier Material materials with Límite elástico of 140 - 250 MPa	for thickness 0.3-0.5 mm \| Transverse
	140 - 230 MPa Show Supplier Material materials with Límite elástico of 140 - 230 MPa	for thickness 0.5-0.7 mm \| Transverse
	140 - 210 MPa Show Supplier Material materials with Límite elástico of 140 - 210 MPa	for thickness 0.7-3 mm \| Transverse
Plastic strain ratio	1.6 [-] Show Supplier Material materials with Plastic strain ratio of 1.6 [-]	min. \| 90ᵒ Transverse \| for thickness 2-3 mm
	1.8 [-] Show Supplier Material materials with Plastic strain ratio of 1.8 [-]	min. \| 90ᵒ Transverse \| for thickness 0.5-2 mm
Resistencia a la fatiga	267 MPa Show Supplier Material materials with Resistencia a la fatiga of 267 MPa	at 5*10⁶ cycles \| for thickness 2 mm
Resistencia a la tracción	270 - 350 MPa Show Supplier Material materials with Resistencia a la tracción of 270 - 350 MPa	for thickness 0.3-3 mm \| Transverse
Strain hardening exponent	0.19 [-] Show Supplier Material materials with Strain hardening exponent of 0.19 [-]	min. \| 90ᵒ Transverse \| for thickness 0.5-3 mm

Chemical properties

Property	Value	Comment
Aluminio	0.02 % Show Supplier Material materials with Aluminio of 0.02 %	max.
Azufre	0.025 % Show Supplier Material materials with Azufre of 0.025 %	max.
Carbono	0.08 % Show Supplier Material materials with Carbono of 0.08 %	max.
Fósforo	0.025 % Show Supplier Material materials with Fósforo of 0.025 %	max.
Manganeso	0.4 % Show Supplier Material materials with Manganeso of 0.4 %	max.
Silicona	0.03 % Show Supplier Material materials with Silicona of 0.03 %	max.

Technological properties

Property
Application areas	Used for bending and deep drawing forming processes for applications where strength, rigidity and ductility are required. Typical applications are to be found in the automotive industry, the domestic appliance sector, metal furniture, drums, radiators, fans, small welded tubes and small profiles. Uncoated cold rolled steels for cold forming are suitable for food contact, under certain conditions laid down in the Regulation (EC) No. 1935/2004 and the French standard NF A 36-714. Please contact us for further information on this subject.
Coating	Galvanisation: Class 1
Surface Finish	This grade is available in: A: for non-visible parts B: for visible parts
Surface condition	Surface cleanliness If improved surface cleanliness is required, ArcelorMittal also offers with compulsory use of hydrogen annealing.
Welding	Weldability is guaranteed when using the usual processes. Please specify which process you intend to use when ordering.
Workability	ArcelorMittal steel grade DC04 for cold forming have excellent drawability in all types of forming processes. They can be used to manufacture complex, multifunctional parts, and allow significant savings. Forming limit curves can be used to define the maximum strains not to be exceeded when forming steel by various methods, so as to avoid the risk of incipient necking. These curves are available on request.