M530YS-65A AM FCE

Nombres alternativos y comerciales
HLE65

Want to keep this datasheet? Save it now in your required format

Description

Non-oriented fully processed high strength grade has not only guaranteed magnetic properties but also guaranteed mechanical properties. Typical for this grade is higher strength values compared with the standard grades, both at room temperature and at higher temperature operating conditions. Full magnetic characterisation curves at different frequencies are available on request.

This high strength grade withstands stronger mechanical forces than the standard grades. It is therefore an excellent compromise when a combination of high mechanical strength and low magnetic losses is required.

Los datos sobre este material han sido proporcionados por ArcelorMittal.

A menos que se indique lo contrario, todas las medidas corresponden a condiciones de temperatura ambiente. A menos que se indique lo contrario, se utilizan las unidades del SI.
Las normas armonizadas son similares a uno o varios estándares del proveedor. Es posible que algunas normas armonizadas se ajusten al estándar original, mientras que otras pueden quedar fuera de su alcance.

Ashby charts

All categories

Propiedades

General

Property	Value
Densidad	7.6 g/cm³ Show Supplier Material materials with Densidad of 7.6 g/cm³

Mecánica

Property	Value	Comment
Dureza Vickers	205 - 235 [-] Show Supplier Material materials with Dureza Vickers of 205 - 235 [-]	Typical values
Elongación	15 % Show Supplier Material materials with Elongación of 15 %	min. \| Guaranteed \| Transverse \| A80
	20 - 30 % Show Supplier Material materials with Elongación of 20 - 30 %	Typical values \| Transverse \| A80
Límite elástico	480 MPa Show Supplier Material materials with Límite elástico of 480 MPa	min. \| Guaranteed \| Transverse
	495 - 545 MPa Show Supplier Material materials with Límite elástico of 495 - 545 MPa	Typical values \| Transverse
Resistencia a la tracción	590 MPa Show Supplier Material materials with Resistencia a la tracción of 590 MPa	min. \| Guaranteed \| Transverse
	610 - 660 MPa Show Supplier Material materials with Resistencia a la tracción of 610 - 660 MPa	Typical values \| Transverse
Yield to strength ratio	0.8 - 0.85 [-] Show Supplier Material materials with Yield to strength ratio of 0.8 - 0.85 [-]	Typical values

Magnético

Property	Value	Frequency	Comment
Polarización garantizada	1.62 [-] Show Supplier Material materials with Polarización garantizada of 1.62 [-]		min. \| at 5000 A/m
Pérdida en el núcleo garantizada	5.3 W/kg Show Supplier Material materials with Pérdida en el núcleo garantizada of 5.3 W/kg	50Hz	max. at 1.5 T

Technological properties

Property

Application areas

High strength values, combined with low losses and good permeability, make this grade particularly suitable for high-speed rotating machines.

Coating

This standard grade is available non-insulated or varnished with any of the coating types described in the following link https://industry.arcelormittal.com/catalogue/D28/EN .

Other

The above properties are obtained without heat treatment after stamping. The material as supplied possesses all the required magnetic properties.

Dimensions:

	Before side trimming		Side trimmed		Slit coils		Sheet length 400 to 2500 mm
	Min width	Max width	Min width	Max width	Min width	Max width	Min width	Max width
M 530YS-65 A AM FCE	1030	1230	600	1200	250	600	400	1100
M 530YS-65 A AM FCE	1030	1230	600	1200	250	600	400	1100

M530YS-65A AM FCE

Description

Ashby charts

Materiales de este proveedor

Propiedades