EN 10025-5 Grade S355J2WP normalized or normalized formed (+N)

View suppliers (6)
Want to keep this datasheet? Save it now in your required format

Description

The weather resistant steel S355J2WP with improved atmospheric corrosion resistance (by generation of an conversion coating) has a minimum yield strength of 355 N/mm². It is applicated for welded, screwed and riveted constructions, e.g. structural engineering, bridge building, tank construction, exhaust systems, vehicle construction, toolbuilding. The grid rate have to considered in the dimensioning process. An conventional surface protection is recommend at polluted air and necessary at long-time water wetting, constant wetness or close to the sea. Unweathered areas with condensate generation have to be adequate ventilated. Before welding the coating have to be removed in a distance of 10 - 20 mm from the welding edge. With increasing thickness, strength and carbon equivalent the occurence of cold cracks in the welding zone is possible. The recommendation of the EURONORM Information No. 2 (EN 1011-2) have to considered. Because of the high amount of P special precautions have to take.

Related Standards

Equivalent Materials

Los datos sobre este material han sido proporcionados por WIAM.

A menos que se indique lo contrario, todas las medidas corresponden a condiciones de temperatura ambiente. A menos que se indique lo contrario, se utilizan las unidades del SI.
Las normas armonizadas son similares a uno o varios estándares del proveedor. Es posible que algunas normas armonizadas se ajusten al estándar original, mientras que otras pueden quedar fuera de su alcance.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

Propiedades

General

PropertyValueComment

Densidad

7.9 - 8.2 g/cm³

Show Material materials with Densidad of 7.9 - 8.2 g/cm³

Typical for Austenitic Stainless Steel

Mecánica

PropertyTemperatureValueConditionRelated StandardsShapeComment

Coeficiente de Poisson

0.3 [-]

Show Material materials with Coeficiente de Poisson of 0.3 [-]

Typical for Austenitic Stainless Steel

Elongación

17.7 %

Show Material materials with Elongación of 17.7 %

Predicted Value, A200

22.5 %

Show Material materials with Elongación of 22.5 %

Predicted Value, A5

23.5 %

Show Material materials with Elongación of 23.5 %

Predicted Value, A50

20 °C

14 %

Show Material materials with Elongación of 14 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

A80 Transverse

20 °C

15 %

Show Material materials with Elongación of 15 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

A80 Transverse

20 °C

16 %

Show Material materials with Elongación of 16 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

A80 Transverse

20 °C

16 %

Show Material materials with Elongación of 16 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

A80

20 °C

17 %

Show Material materials with Elongación of 17 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

A80

20 °C

18 %

Show Material materials with Elongación of 18 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

A80

20 °C

20 %

Show Material materials with Elongación of 20 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Transverse

20 °C

22 %

Show Material materials with Elongación of 22 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Límite elástico

263.2 MPa

Show Material materials with Límite elástico of 263.2 MPa

Predicted Value, RP1

285.9 MPa

Show Material materials with Límite elástico of 285.9 MPa

Predicted Value, RP1 Transverse

354.3 MPa

Show Material materials with Límite elástico of 354.3 MPa

Predicted Value, RP05

377.5 MPa

Show Material materials with Límite elástico of 377.5 MPa

Predicted Value, RP02 Transverse

388.1 MPa

Show Material materials with Límite elástico of 388.1 MPa

Predicted Value, RP02

489.8 MPa

Show Material materials with Límite elástico of 489.8 MPa

Predicted Value, RP002

20 °C

345 MPa

Show Material materials with Límite elástico of 345 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

Transverse

20 °C

345 MPa

Show Material materials with Límite elástico of 345 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

20 °C

355 MPa

Show Material materials with Límite elástico of 355 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

Transverse

20 °C

355 MPa

Show Material materials with Límite elástico of 355 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Módulo de cizallamiento

77 GPa

Show Material materials with Módulo de cizallamiento of 77 GPa

Typical for Austenitic Stainless Steel

Módulo elástico

195 GPa

Show Material materials with Módulo elástico of 195 GPa

Typical for Austenitic Stainless Steel

Resistencia a la tracción

20 °C

470 - 680 MPa

Show Material materials with Resistencia a la tracción of 470 - 680 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

Transverse

20 °C

470 - 630 MPa

Show Material materials with Resistencia a la tracción of 470 - 630 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

Transverse

20 °C

470 - 680 MPa

Show Material materials with Resistencia a la tracción of 470 - 680 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

20 °C

470 - 630 MPa

Show Material materials with Resistencia a la tracción of 470 - 630 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

20 °C

490 - 680 MPa

Show Material materials with Resistencia a la tracción of 490 - 680 MPa

normalized or normalized formed (+N)

EN 10155, EN 10025-1, EN 10025-5

Bar, Sheet, Strip, Flat

20 °C

490 - 630 MPa

Show Material materials with Resistencia a la tracción of 490 - 630 MPa

normalized or normalized formed (+N)

EN 10155, EN 10025-1, EN 10025-5

Bar, Sheet, Strip, Flat

20 °C

510 - 680 MPa

Show Material materials with Resistencia a la tracción of 510 - 680 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

Transverse

20 °C

510 - 630 MPa

Show Material materials with Resistencia a la tracción of 510 - 630 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

Transverse

20 °C

510 - 680 MPa

Show Material materials with Resistencia a la tracción of 510 - 680 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

20 °C

510 - 630 MPa

Show Material materials with Resistencia a la tracción of 510 - 630 MPa

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Aplicaciones térmicas

PropertyValueComment

Calor específico

440 J/(kg·K)

Show Material materials with Calor específico of 440 J/(kg·K)

Typical for Austenitic Stainless Steel

Coeficiente de dilatación térmica

1.7e-05 - 1.9e-05 1/K

Show Material materials with Coeficiente de dilatación térmica of 1.7e-05 - 1.9e-05 1/K

Typical for Austenitic Stainless Steel

Conductividad térmica

11 - 21 W/(m·K)

Show Material materials with Conductividad térmica of 11 - 21 W/(m·K)

Typical for Austenitic Stainless Steel

Temperatura de fusión

1230 - 1480 °C

Show Material materials with Temperatura de fusión of 1230 - 1480 °C

Typical for Austenitic Stainless Steel

Eléctrico

PropertyValueComment

Resistividad eléctrica

8.5e-07 Ω·m

Show Material materials with Resistividad eléctrica of 8.5e-07 Ω·m

Typical for Austenitic Stainless Steel

Chemical properties

PropertyValueConditionRelated StandardsShape

Azufre

0.03 %

Show Material materials with Azufre of 0.03 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155

Strip, Sheet, Flat, Rod, Wire

0.035 %

Show Material materials with Azufre of 0.035 %

normalized or normalized formed (+N)

EN 10155, EN 10025-1, EN 10025-5

Bar, Sheet, Strip, Flat

Carbono

0.12 %

Show Material materials with Carbono of 0.12 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Cobre

0.25 - 0.55 %

Show Material materials with Cobre of 0.25 - 0.55 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Cromo

0.3 - 1.25 %

Show Material materials with Cromo of 0.3 - 1.25 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Fósforo

0.06 - 0.15 %

Show Material materials with Fósforo of 0.06 - 0.15 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Manganeso

1 %

Show Material materials with Manganeso of 1 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Níquel

0.65 %

Show Material materials with Níquel of 0.65 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar

Silicona

0.75 %

Show Material materials with Silicona of 0.75 %

normalized or normalized formed (+N)

EN 10025-5, EN 10155, EN 10025-1

Strip, Sheet, Flat, Rod, Wire, Bar