EN 10025-2 Grade S355J0C as-rolled condition (+AR)

Want to keep this datasheet? Save it now in your required format

Description

S355J0C is used for folding, section cold forming and cold drawing grade. The high-tensile fine grained steel is applicable for welding constructions up to -20 °C subject to the load. Compared to S235J0C is achievable a considerable saving of material due to the by 120 MPa higher yield point. The steel shows a by 15% higher resistance to mineral wear due to sliding action in comparison to S235J0. Max. product thickness amounts 20 mm for folding and 8 mm for cold roll forming grades.

Related Standards

Equivalent Materials

Los datos sobre este material han sido proporcionados por WIAM.

A menos que se indique lo contrario, todas las medidas corresponden a condiciones de temperatura ambiente. A menos que se indique lo contrario, se utilizan las unidades del SI.
Las normas armonizadas son similares a uno o varios estándares del proveedor. Es posible que algunas normas armonizadas se ajusten al estándar original, mientras que otras pueden quedar fuera de su alcance.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

All categories

Propiedades

General

Property	Value	Comment
Densidad	7.8 - 7.9 g/cm³ Show Material materials with Densidad of 7.8 - 7.9 g/cm³	Typical for Low Carbon Steel

Mecánica

Property	Temperature	Value	Condition	Related Standards	Shape	Comment
Coeficiente de Poisson		0.29 [-] Show Material materials with Coeficiente de Poisson of 0.29 [-]				Typical for Low Carbon Steel
Elongación		17.1 % Show Material materials with Elongación of 17.1 %				Predicted Value, A200
		21.8 % Show Material materials with Elongación of 21.8 %				Predicted Value, A5
		23.2 % Show Material materials with Elongación of 23.2 %				Predicted Value, A50
	20 °C	12 % Show Material materials with Elongación of 12 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80 Transverse
	20 °C	13 % Show Material materials with Elongación of 13 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80 Transverse
	20 °C	14 % Show Material materials with Elongación of 14 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80 Transverse
	20 °C	15 % Show Material materials with Elongación of 15 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80 Transverse
	20 °C	16 % Show Material materials with Elongación of 16 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80 Transverse
	20 °C	16 % Show Material materials with Elongación of 16 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80
	20 °C	17 % Show Material materials with Elongación of 17 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80
	20 °C	18 % Show Material materials with Elongación of 18 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat	A80
	20 °C	20 % Show Material materials with Elongación of 20 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Flat, Bar, Sheet, Strip	Transverse
	20 °C	22 % Show Material materials with Elongación of 22 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Flat, Bar, Sheet, Strip
Estricción		41.0 % Show Material materials with Estricción of 41.0 %				Predicted Value
		43.7 % Show Material materials with Estricción of 43.7 %				Predicted Value, Transverse
Límite elástico		254.2 MPa Show Material materials with Límite elástico of 254.2 MPa				Predicted Value, RP1
		316.5 MPa Show Material materials with Límite elástico of 316.5 MPa				Predicted Value, RP1 Transverse
		350.6 MPa Show Material materials with Límite elástico of 350.6 MPa				Predicted Value, Transverse
		355.9 MPa Show Material materials with Límite elástico of 355.9 MPa				Predicted Value, RP02
		366.5 MPa Show Material materials with Límite elástico of 366.5 MPa				Predicted Value, RP05
		446.5 MPa Show Material materials with Límite elástico of 446.5 MPa				Predicted Value, RP02 Transverse
		482.8 MPa Show Material materials with Límite elástico of 482.8 MPa				Predicted Value, RP002
	20 °C	345 MPa Show Material materials with Límite elástico of 345 MPa	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
	20 °C	355 MPa Show Material materials with Límite elástico of 355 MPa	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
Módulo de cizallamiento		82 GPa Show Material materials with Módulo de cizallamiento of 82 GPa				Typical for Low Carbon Steel
Módulo elástico		200 - 215 GPa Show Material materials with Módulo elástico of 200 - 215 GPa				Typical for Low Carbon Steel
Resistencia a la tracción	20 °C	490 - 630 MPa Show Material materials with Resistencia a la tracción of 490 - 630 MPa	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
	20 °C	490 - 680 MPa Show Material materials with Resistencia a la tracción of 490 - 680 MPa	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat
	20 °C	510 - 680 MPa Show Material materials with Resistencia a la tracción of 510 - 680 MPa	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat
	20 °C	510 - 630 MPa Show Material materials with Resistencia a la tracción of 510 - 630 MPa	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Sheet, Strip, Flat
Resistencia al cizallamiento		513.2 MPa Show Material materials with Resistencia al cizallamiento of 513.2 MPa				Predicted Value

Aplicaciones térmicas

Property	Value	Condition	Related Standards	Shape	Comment
Calor específico	465 J/(kg·K) Show Material materials with Calor específico of 465 J/(kg·K)				Typical for Low Carbon Steel
Coeficiente de dilatación térmica	1.32e-05 - 1.38e-05 1/K Show Material materials with Coeficiente de dilatación térmica of 1.32e-05 - 1.38e-05 1/K				Typical for Low Carbon Steel
Conductividad térmica	25 - 93 W/(m·K) Show Material materials with Conductividad térmica of 25 - 93 W/(m·K)				Typical for Low Carbon Steel
Temperatura de fusión	1480 - 1526 °C Show Material materials with Temperatura de fusión of 1480 - 1526 °C				Typical for Low Carbon Steel
Temperatura máx. de funcionamiento	-20 °C Show Material materials with Temperatura máx. de funcionamiento of -20 °C	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat	Long
	500 °C Show Material materials with Temperatura máx. de funcionamiento of 500 °C				Typical for Carbon Steel

Eléctrico

Property	Value	Comment
Conductividad eléctrica	8 S/m Show Material materials with Conductividad eléctrica of 8 S/m	Predicted Value
Resistividad eléctrica	1.43e-07 - 1.74e-07 Ω·m Show Material materials with Resistividad eléctrica of 1.43e-07 - 1.74e-07 Ω·m	Typical for Carbon Steel

Magnético

Property	Value	Comment
Temperatura de Curie	770 °C Show Material materials with Temperatura de Curie of 770 °C	Typical for Low Carbon Steel

Chemical properties

Property	Value	Condition	Related Standards	Shape
Azufre	0.04 % Show Material materials with Azufre of 0.04 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
Carbono	0.2 % Show Material materials with Carbono of 0.2 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
Fósforo	0.04 % Show Material materials with Fósforo of 0.04 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
Manganeso	1.6 % Show Material materials with Manganeso of 1.6 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
Nitrógeno	0.009 % Show Material materials with Nitrógeno of 0.009 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat
Silicona	0.55 % Show Material materials with Silicona of 0.55 %	as-rolled condition (+AR)	EN 10025, EN 10025-1, EN 10025-2	Bar, Sheet, Strip, Flat

Technological properties

Property
Supplier Disclaimer	The given information is a rough description and some properties can depend on various factors such as product thickness. Please contact the supplier or refer to the related norm or standard for further information.

Looking for suppliers of this material? Click to see 3 supplier of EN 10025-2 Grade S355J0C as-rolled condition (+AR) on Matmatch