DIN 1725-1 Grade 3.4345 T6

Want to keep this datasheet? Save it now in your required format

Description

The alloy AlZnMgCu0,5 belongs to the aluminum materials, which achieve very high mechanical strength. With hot ageing the strength grade F 49 is attainable. This alloy is good splinter-giving machinably. The alloy is weldable with consideration of certain conditions, especially a heat influence zone with small strength appears there. One should not weld therefore if possible. A good corrosion resistance can be only guaranteed, if an appropriate protective surface layer is present. The corrosion resistance improves noticeably also by hot ageing. Roll-plating of sheet metals of this alloy e.g. with AlZn1 will support the small corrosion resistance with exhaust the high mechanical strenght fully. Thus the area of application extends noticeably. This alloy possesses well splinter-giving workability. Heat treatment for hardening: solution annealing: 470 to 480 °C, quenching in water hot ageing: 12 to 24 h at 115 to 125 °C, 4 to 6 h at 165 to 180 °C (two stage ageing) cold ageing is uncommon Application: In mechanical engineering for devices, tools. Predominantly tension-poor strained sheet metals for baseplates, head and stamp retaining plates as well as in the automobile engineering for safety-related parts and bumpers.

Related Standards

Equivalent Materials

Los datos sobre este material han sido proporcionados por WIAM,AluKey.

A menos que se indique lo contrario, todas las medidas corresponden a condiciones de temperatura ambiente. A menos que se indique lo contrario, se utilizan las unidades del SI.
Las normas armonizadas son similares a uno o varios estándares del proveedor. Es posible que algunas normas armonizadas se ajusten al estándar original, mientras que otras pueden quedar fuera de su alcance.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

All categories

Lectura sugerida

6061-T6 Aluminium – The Ultimate Guide

7075-T6 Aluminium: Overview & Properties

Aircraft Aluminium Grades

Cast vs. Wrought Aluminium: Standards, Properties and Applications

Precipitation Hardening (Age Hardening)

Mostrar todo

Do you supply similar materials?

List your company on Matmatch now and reach engineers around the world looking for such materials.

Request more information

Propiedades

General

Property	Temperature	Value	Condition	Related Standards	Shape
Densidad		2.78 g/cm³ Show Material materials with Densidad of 2.78 g/cm³	T6	EN 573-3, EN 485, EN 754, EN 755
	20.0 °C	2.78 g/cm³ Show Material materials with Densidad of 2.78 g/cm³	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging

Mecánica

Property	Temperature	Value	Condition	Related Standards	Shape	Comment
Coeficiente de Poisson		0.33 [-] Show Material materials with Coeficiente de Poisson of 0.33 [-]				Typical for Wrought 7000 Series Aluminium
Dureza Brinell		121.0 [-] Show Material materials with Dureza Brinell of 121.0 [-]	T6	EN 573-3, EN 485
		127.0 [-] Show Material materials with Dureza Brinell of 127.0 [-]	T6	EN 573-3, EN 485
		133.0 [-] Show Material materials with Dureza Brinell of 133.0 [-]	T6	EN 573-3, EN 485
	20.0 °C	130.0 [-] Show Material materials with Dureza Brinell of 130.0 [-]	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	135.0 [-] Show Material materials with Dureza Brinell of 135.0 [-]	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
Elongación		3.0 % Show Material materials with Elongación of 3.0 %	T6	EN 573-3, EN 485		A100
		5.0 % Show Material materials with Elongación of 5.0 %	T6	EN 573-3, EN 485		A100
		5.0 % Show Material materials with Elongación of 5.0 %	T6	EN 573-3, EN 755		A50
		6.0 % Show Material materials with Elongación of 6.0 %	T6	EN 573-3, EN 754		A50
		7.0 % Show Material materials with Elongación of 7.0 %	T6	EN 573-3, EN 485, EN 755		A100
		8.0 % Show Material materials with Elongación of 8.0 %	T6	EN 573-3, EN 485, EN 754		A100
		8.0 % Show Material materials with Elongación of 8.0 %	T6	EN 573-3, EN 485, EN 754		A50
	20.0 °C	2.0 % Show Material materials with Elongación of 2.0 %	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	3.0 % Show Material materials with Elongación of 3.0 %	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	4.0 % Show Material materials with Elongación of 4.0 %	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	6.0 % Show Material materials with Elongación of 6.0 %	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
Módulo de cizallamiento	20.0 °C	27.5 GPa Show Material materials with Módulo de cizallamiento of 27.5 GPa	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
Módulo elástico		70.0 GPa Show Material materials with Módulo elástico of 70.0 GPa	T6	EN 573-3, EN 485, EN 754, EN 755
	20.0 °C	72.0 GPa Show Material materials with Módulo elástico of 72.0 GPa	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
Plane-Strain Fracture Toughnes		22.0 - 35.0 MPa·√m Show Material materials with Plane-Strain Fracture Toughnes of 22.0 - 35.0 MPa·√m				Typical for Wrought 7000 Series Aluminium
Resistencia a la tracción		410.0 MPa Show Material materials with Resistencia a la tracción of 410.0 MPa	T6	EN 573-3, EN 485
		430.0 MPa Show Material materials with Resistencia a la tracción of 430.0 MPa	T6	EN 573-3, EN 485
		450.0 MPa Show Material materials with Resistencia a la tracción of 450.0 MPa	T6	EN 573-3, EN 485
		460.0 MPa Show Material materials with Resistencia a la tracción of 460.0 MPa	T6	EN 573-3, EN 754
		470.0 MPa Show Material materials with Resistencia a la tracción of 470.0 MPa	T6	EN 573-3, EN 755
		490.0 MPa Show Material materials with Resistencia a la tracción of 490.0 MPa	T6	EN 573-3, EN 755
	20.0 °C	440.0 MPa Show Material materials with Resistencia a la tracción of 440.0 MPa	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	450.0 MPa Show Material materials with Resistencia a la tracción of 450.0 MPa	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	460.0 MPa Show Material materials with Resistencia a la tracción of 460.0 MPa	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	470.0 MPa Show Material materials with Resistencia a la tracción of 470.0 MPa	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	20.0 °C	480.0 MPa Show Material materials with Resistencia a la tracción of 480.0 MPa	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging

Aplicaciones térmicas

Property	Temperature	Value	Condition	Related Standards	Shape	Comment
Calor específico		795.0 - 1050.0 J/(kg·K) Show Material materials with Calor específico of 795.0 - 1050.0 J/(kg·K)				Typical for Wrought 7000 Series Aluminium
Coeficiente de dilatación térmica	20 °C	2.36e-05 1/K Show Material materials with Coeficiente de dilatación térmica of 2.36e-05 1/K	T6	EN 573-3, EN 485, EN 754, EN 755
	100 °C	2.36e-05 1/K Show Material materials with Coeficiente de dilatación térmica of 2.36e-05 1/K	T6	EN 573-3, EN 485, EN 754, EN 755
Conductividad térmica	20.0 °C	130.0 - 160.0 W/(m·K) Show Material materials with Conductividad térmica of 130.0 - 160.0 W/(m·K)	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging
Temperatura de fusión		480.0 - 640.0 °C Show Material materials with Temperatura de fusión of 480.0 - 640.0 °C	T6	EN 573-3, EN 485, EN 754, EN 755

Eléctrico

Property	Temperature	Value	Condition	Related Standards	Shape
Conductividad eléctrica	20.0 °C	19000000.0 - 23000000.0 S/m Show Material materials with Conductividad eléctrica of 19000000.0 - 23000000.0 S/m	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging
Resistividad eléctrica		4.35e-08 - 5.26e-08 Ω·m Show Material materials with Resistividad eléctrica of 4.35e-08 - 5.26e-08 Ω·m	T6	EN 573-3, EN 485, EN 754, EN 755

Chemical properties

Property	Value	Condition	Related Standards	Shape
Cobre	0.5 - 1.0 % Show Material materials with Cobre of 0.5 - 1.0 %	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging
Cromo	0.1 - 0.3 % Show Material materials with Cromo of 0.1 - 0.3 %	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging
Hierro	0.5 % Show Material materials with Hierro of 0.5 %	T6	DIN 1725-1, EN 573-3, EN 573-4	Forging
	0.50 % Show Material materials with Hierro of 0.50 %	T6	EN 573-3, EN 485, EN 754, EN 755
Magnesio	2.6 - 3.7 % Show Material materials with Magnesio of 2.6 - 3.7 %	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging
Manganeso	0.1 - 0.4 % Show Material materials with Manganeso of 0.1 - 0.4 %	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging
Silicona	0.5 % Show Material materials with Silicona of 0.5 %	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging
Zinc	4.3 - 5.2 % Show Material materials with Zinc of 4.3 - 5.2 %	T6	DIN 1725-1, EN 573-3, EN 573-4, EN 485, EN 754, EN 755	Forging

Technological properties

Property
Anodizing	decorative: not suitable, Protective: good
Brazing	hard brazing (with flux/ without flux): not suitable / not suitable, friction soldering: not suitable, soft brazing with flux: not suitable
Corrosion properties	Seawater: poor, weathering: sufficient
Workability	Bending / Spinning (cold): poor (O) / not suitable, Impact extrusion (cold): not suitable, Deep drawing / upsetting (Condition) not suitable / not suitable

Looking for suppliers of this material? Click to see 3 supplier of DIN 1725-1 Grade 3.4345 T6 on Matmatch