Pebax® Rnew® 30R51 SA 01

Nombres alternativos y comerciales
TPA

Want to keep this datasheet? Save it now in your required format

Description

Polyether block Pebax® Rnew® 30R51 SA 01 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide based on renewable resources.

Pebax® Rnew® 30R51 SA 01 resin is an inherently antistatic polymer and can be dry blended or compounded with a polymer matrix to lower the surface resistivity of the final part. This grade is particularly recommended for PMMA matrices. This hydrophilic grade when extruded into either a thin film or laminated on to a substrate offers excellent permeability to moisture vapor while remaining waterproof. The percentage of renewable carbon according to ASTM D6866 is 41%

. Refractive index according to an internal method is 1.49.

Los datos sobre este material han sido proporcionados por Arkema Technical Polymers.

A menos que se indique lo contrario, todas las medidas corresponden a condiciones de temperatura ambiente. A menos que se indique lo contrario, se utilizan las unidades del SI.
Las normas armonizadas son similares a uno o varios estándares del proveedor. Es posible que algunas normas armonizadas se ajusten al estándar original, mientras que otras pueden quedar fuera de su alcance.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

All categories

Propiedades

General

Property	Value	Testing Standard	Condition
Absorción de agua	20 % Show Supplier Material materials with Absorción de agua of 20 %	Sim. to ISO 62
Bio-based content	41 % Show Supplier Material materials with Bio-based content of 41 %
Densidad	1.01 g/cm³ Show Supplier Material materials with Densidad of 1.01 g/cm³	ISO 1183	dry
Moisture absorption	2.5 % Show Supplier Material materials with Moisture absorption of 2.5 %	Sim. to ISO 62

Mecánica

Property	Value	Condition	Testing Standard	Comment
Dureza Shore D	30 [-] Show Supplier Material materials with Dureza Shore D of 30 [-]	dry	ISO 7619-1	15 seconds
Elongación	50 % Show Supplier Material materials with Elongación of 50 %	cond.	ISO 527-1/-2	min.
Módulo elástico	0.059 GPa Show Supplier Material materials with Módulo elástico of 0.059 GPa	cond.	ISO 527-1/-2

Aplicaciones térmicas

Property	Value	Condition	Testing Standard	Comment
Temperatura de fusión	150 °C Show Supplier Material materials with Temperatura de fusión of 150 °C	dry	ISO 11357-1/-3	10°C/min

Eléctrico

Property	Value	Condition	Testing Standard
Surface resistivity	1e+08 Ω/sq Show Supplier Material materials with Surface resistivity of 1e+08 Ω/sq	cond.	IEC 60093
Volume resistivity	1e+08 Ω·cm Show Supplier Material materials with Volume resistivity of 1e+08 Ω·cm	cond.	IEC 60093
	1e+10 Ω·cm Show Supplier Material materials with Volume resistivity of 1e+10 Ω·cm	dry	IEC 60093

Technological properties

Property

Application areas

Breathable Films - Housewrap,Permanent Antistatic Solutions,Eyewear Frames,Permanent Antistatic Solutions E&E

Processing methods

Injection Molding:

Typical melt temperature (Min / Recommended / Max): 200°C / 240°C / 270°C.

Typical mold temperature: 25–60°C.

Drying time and temperature (only necessary for bags opened for more than two hours): 4-6 hours at 65-75°C.

Extrusion:

Typical melt temperature (Min / Recommended / Max): 210°C / 220°C / 230°C.

Drying time and temperature (only necessary for bags opened for more than two hours): 4-6 hours at 65-75°C.

Pebax® Rnew® 30R51 SA 01

Description

Ashby charts

Usos

Materiales de este proveedor

Propiedades