Zytel® 80G33HS1L NC010

Nombres alternativos y comerciales
PA66-I-GF33

Want to keep this datasheet? Save it now in your required format

Description

Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.Zytel® 80G33HS1L NC010 is a 33% glass fiber reinforced heat stabilized polyamide 66 resin with outstanding impact resistance developed using DuPont Super Tough technology.

Equivalent Materials

Los datos sobre este material han sido proporcionados por Matmatch.

A menos que se indique lo contrario, todas las medidas corresponden a condiciones de temperatura ambiente. A menos que se indique lo contrario, se utilizan las unidades del SI.
Las normas armonizadas son similares a uno o varios estándares del proveedor. Es posible que algunas normas armonizadas se ajusten al estándar original, mientras que otras pueden quedar fuera de su alcance.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

All categories

Propiedades

General

Property	Temperature	Value	Comment
Absorción de agua	23.0 °C	0.85 % Show Material materials with Absorción de agua of 0.85 %	Sim. to ISO 62 \| Immersion 24h
Densidad	23.0 °C	1.33 g/cm³ Show Material materials with Densidad of 1.33 g/cm³	ISO 1183

Mecánica

Property	Temperature	Value	Comment
Coeficiente de Poisson	23.0 °C	0.34 [-] Show Material materials with Coeficiente de Poisson of 0.34 [-]
Dureza Rockwell M	23.0 °C	70 [-] Show Material materials with Dureza Rockwell M of 70 [-]	ISO 2039-2
Elongación	23.0 °C	3.7 % Show Material materials with Elongación of 3.7 %	ISO 527-1/-2
Hardness, Ball Indentation	23.0 °C	220 MPa Show Material materials with Hardness, Ball Indentation of 220 MPa	ISO 2039-1
Hardness, Rockwell R	23.0 °C	110 [-] Show Material materials with Hardness, Rockwell R of 110 [-]	ISO 2039-2
Módulo de flexión	23.0 °C	7.5 GPa Show Material materials with Módulo de flexión of 7.5 GPa	ISO 178
Módulo elástico	23.0 °C	8.9 GPa Show Material materials with Módulo elástico of 8.9 GPa	ISO 527-1/-2
Resistencia a la flexión	23.0 °C	205 MPa Show Material materials with Resistencia a la flexión of 205 MPa	ISO 178
Resistencia a la tracción	23.0 °C	146 MPa Show Material materials with Resistencia a la tracción of 146 MPa	ISO 527-1/-2
Resistencia al choque, ensayo Charpy entallado	-40.0 °C	14 kJ/m² Show Material materials with Resistencia al choque, ensayo Charpy entallado of 14 kJ/m²	ISO 179/1eA
	-6.0 °C	18 kJ/m² Show Material materials with Resistencia al choque, ensayo Charpy entallado of 18 kJ/m²	ISO 179/1eA
	23.0 °C	20 kJ/m² Show Material materials with Resistencia al choque, ensayo Charpy entallado of 20 kJ/m²	ISO 179/1eA

Resistencia al choque, ensayo Charpy no entallado	-6.0 °C	106 kJ/m² Show Material materials with Resistencia al choque, ensayo Charpy no entallado of 106 kJ/m²	ISO 179/1eU
	23.0 °C	97 kJ/m² Show Material materials with Resistencia al choque, ensayo Charpy no entallado of 97 kJ/m²	ISO 179/1eU
	Unlock all property charts
Resistencia al choque, ensayo Izod entallado	-30.0 °C	80 kJ/m² Show Material materials with Resistencia al choque, ensayo Izod entallado of 80 kJ/m²	ISO 180/1U
	23.0 °C	80 kJ/m² Show Material materials with Resistencia al choque, ensayo Izod entallado of 80 kJ/m²	ISO 180/1U
	Unlock all property charts
Resistencia al choque, ensayo Izod no entallado	-40.0 °C	15 kJ/m² Show Material materials with Resistencia al choque, ensayo Izod no entallado of 15 kJ/m²	ISO 180/1A
	-30.0 °C	17 kJ/m² Show Material materials with Resistencia al choque, ensayo Izod no entallado of 17 kJ/m²	ISO 180/1A
	23.0 °C	21 kJ/m² Show Material materials with Resistencia al choque, ensayo Izod no entallado of 21 kJ/m²	ISO 180/1A
	Unlock all property charts

Aplicaciones térmicas

Property	Temperature	Value	Comment
Calor específico	23.0 °C	2200 J/(kg·K) Show Material materials with Calor específico of 2200 J/(kg·K)	of melt
Coeficiente de dilatación térmica	23.0 °C	1.5E-5 1/K Show Material materials with Coeficiente de dilatación térmica of 1.5E-5 1/K	ISO 11359-1/-2
Coeficiente de dilatación térmica transversal	23.0 °C	1.2E-4 1/K Show Material materials with Coeficiente de dilatación térmica transversal of 1.2E-4 1/K	ISO 11359-1/-2
Difusividad térmica	23.0 °C	0 mm²/s Show Material materials with Difusividad térmica of 0 mm²/s
Heat deflection temperature, 0.45 MPa		261 °C Show Material materials with Heat deflection temperature, 0.45 MPa of 261 °C	ISO 75-1/-2
Heat deflection temperature, 1.80 MPa		246 °C Show Material materials with Heat deflection temperature, 1.80 MPa of 246 °C	ISO 75-1/-2
Relative temperature index, electrical		130 °C Show Material materials with Relative temperature index, electrical of 130 °C	UL 746B \| 120mil
Relative temperature index, mechanical impact		105 °C Show Material materials with Relative temperature index, mechanical impact of 105 °C	UL 746B \| 120mil
Relative temperature index, mechanical strength		105 °C Show Material materials with Relative temperature index, mechanical strength of 105 °C	UL 746B \| 120mil
Temperatura de fusión		262 °C Show Material materials with Temperatura de fusión of 262 °C	ISO 11357-1/-3 \| 18°F/min
Temperatura de reblandecimiento Vicat		245 °C Show Material materials with Temperatura de reblandecimiento Vicat of 245 °C	ISO 306 \| 90°F/h, 11 lbf
Temperatura de transición del vidrio		75 °C Show Material materials with Temperatura de transición del vidrio of 75 °C	ISO 11357-1/-2 \| 18°F/min
Inflamabilidad	Burning Behav. at 60mil nom. thickn.: HB class, Thickness tested: 1.5 mm, UL recognition: yes -, Burning Behav. at thickness h: HB class, Thickness tested: 0.75 mm, UL recognition: yes -, Glow Wire Flammability Index, 40mil: 650 °C, Glow Wire Flammability Index, 80mil: 700 °C, Glow Wire Flammability Index, 120mil: 900 °C, Glow Wire Ignition Temperature, 40mil: 700 °C, Glow Wire Ignition Temperature, 80mil: 700 °C, Glow Wire Ignition Temperature, 120mil: 750 °C, FMVSS Class: SE -, Burning rate, Thickness 1 mm: 23 mm/min

Eléctrico

Property	Temperature	Value	Comment
Constante dieléctrica, 1 MHz	23.0 °C	3.6 [-] Show Material materials with Constante dieléctrica, 1 MHz of 3.6 [-]	IEC 62631-2-1
Dissipation factor, 1MHz	23.0 °C	0.01 [-] Show Material materials with Dissipation factor, 1MHz of 0.01 [-]	IEC 62631-2-1
Volume resistivity	23.0 °C	1.00E+15 Ω·cm Show Material materials with Volume resistivity of 1.00E+15 Ω·cm	min. \| IEC 62631-3-1

Rheological Properties

Property	Temperature	Value	Comment
Contracción	23.0 °C	0.3 % Show Material materials with Contracción of 0.3 %	ISO 294-4, 2577
Contracción transversal	23.0 °C	0.7 % Show Material materials with Contracción transversal of 0.7 %	ISO 294-4, 2577

Technological properties

Property
Fillers	33% Glass Fiber
Processing methods	Drying Recommended: yes, Drying Temperature: 80°C, Drying Time, Dehumidified Dryer: 2-4h, Processing Moisture Content: ≤0.2%, Melt Temperature Optimum: 295°C, Min. melt temperature: 285°C, Max. melt temperature: 305°C, Max. screw tangential speed: 0.2m/s, Mold Temperature Optimum: 80°C, Min. mold temperature: 50°C, Max. mold temperature: 100°C, Hold pressure range: 50-100MPa, Hold pressure time: 3s/mm, Ejection temperature: 210°C

Zytel® 80G33HS1L NC010

Description

Equivalent Materials

Ashby charts

Lectura sugerida

Propiedades