EN 12168 Grade CuSP H080

Want to keep this datasheet? Save it now in your required format

Description

CuSP, mat. No CW114C, is counted among unhardenable, low alloyed copper alloys. To the comparable make CuSP, mat. No 2.1498, acc. to DIN 17666 : 1983-12 applies: A strength increase is achievable only by cold forming. Already low S-contents increase the temperature for removal of workhardening to approx. 300°C. CuSP shows roughly the same electrical and thermal conductivity as pure copper. The corrosion resistance is equal to unalloyed copper. Processing properties: hot forming: moderately cold forming: good machinability: very good soft soldering: good hard soldering: moderately gas shielded welding: unfavorable burnishing: good Application: For screw machine parts and clamps in electronics, for nozzle, welding and cutting torches as well as for engine parts, valves and fittings.

Related Standards

Equivalent Materials

This material data has been provided by WIAM.

All metrics apply to room temperature unless otherwise stated. SI units used unless otherwise stated.
Equivalent standards are similar to one or more standards provided by the supplier. Some equivalent standards may be stricter whereas others may be outside the bounds of the original standard.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

Properties

General

PropertyTemperatureValue

Density

20.0 °C

8.9 g/cm³

Show Material materials with Density of 8.9 g/cm³

Mechanical

PropertyTemperatureValueComment

Elastic modulus

20.0 °C

120 GPa

Show Material materials with Elastic modulus of 120 GPa

Hardness, Brinell

20.0 °C

80 - 130 [-]

Show Material materials with Hardness, Brinell of 80 - 130 [-]

Hardness, Vickers

20.0 °C

90 - 140 [-]

Show Material materials with Hardness, Vickers of 90 - 140 [-]

Poisson's ratio

23.0 °C

0.34 [-]

Show Material materials with Poisson's ratio of 0.34 [-]

Typical for Wrought Copper Pure / Low Alloyed Copper

Shear modulus

23.0 °C

48 GPa

Show Material materials with Shear modulus of 48 GPa

Typical for Wrought Copper Pure / Low Alloyed Copper

Tensile strength

20.0 °C

250 MPa

Show Material materials with Tensile strength of 250 MPa

Yield strength Rp0.2

20.0 °C

200 MPa

Show Material materials with Yield strength Rp0.2 of 200 MPa

Thermal

PropertyTemperatureValueComment

Coefficient of thermal expansion

100.0 °C

1.69E-5 1/K

Show Material materials with Coefficient of thermal expansion of 1.69E-5 1/K

200.0 °C

1.73E-5 1/K

Show Material materials with Coefficient of thermal expansion of 1.73E-5 1/K

300.0 °C

1.76E-5 1/K

Show Material materials with Coefficient of thermal expansion of 1.76E-5 1/K

Melting point

965 - 1100 °C

Show Material materials with Melting point of 965 - 1100 °C

Typical for Wrought Copper Pure / Low Alloyed Copper

Specific heat capacity

20.0 °C

385 J/(kg·K)

Show Material materials with Specific heat capacity of 385 J/(kg·K)

100.0 °C

394 J/(kg·K)

Show Material materials with Specific heat capacity of 394 J/(kg·K)

200.0 °C

406 J/(kg·K)

Show Material materials with Specific heat capacity of 406 J/(kg·K)

Unlock all property charts

Thermal conductivity

20.0 °C

374 W/(m·K)

Show Material materials with Thermal conductivity of 374 W/(m·K)

Electrical

PropertyTemperatureValue

Electrical conductivity

20.0 °C

5.00E+7 S/m

Show Material materials with Electrical conductivity of 5.00E+7 S/m

Specific Electrical conductivity

86 % IACS

Show Material materials with Specific Electrical conductivity of 86 % IACS

Chemical properties

PropertyValue

Phosphorus

0 - 0.01 %

Show Material materials with Phosphorus of 0 - 0.01 %

Sulfur

0.2 - 0.7 %

Show Material materials with Sulfur of 0.2 - 0.7 %