Transparent PC. ILLUMINATE special effects (fluorescent/edge glow colors). MFR 10.1. Internal mold release.
See where LEXAN™ Copolymer FXE141R falls on the material property chart for Density against Elastic modulus in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.
Density
ρ1.19 g/cm³ at 23 °C
ASTM D 792
Moisture absorption
cmoisture0.15 % at 23 °C
ISO 62 | (23°C / 50% RH)
Relative density
ρrel1.2 [-] at 23 °C
ASTM D 792
Specific volume
v0.83 cm³/g at 23 °C
ASTM D 792
Water absorption
cwater0.35 % at 23 °C
ISO 62-1 | (23°C/saturated)
Impact strength, Charpy unnotched Iunnot
ISO 179/1eU | Unnotch Edgew 80*10*3 sp=62mm, -30°C
Impact strength, Izod unnotched IIzod,unnot
ISO 180/1U | 80*10*3, 23°C
Ball Pressure Test
nan
Coefficient of thermal expansion
α7E-5 1/K at 23 °C
ISO 11359-2 | 23°C to 80°C
Flammability
UL Yellow Card Link: https://iq.ul.com/ul/cert.aspx?ULID=228425 | UL Recognized, 94HB Flame Class Rating: 0.7 mm UL 94 | UV-light, water exposure/immersion: F2 - UL 746C | UL Yellow Card Link 2: https://iq.ul.com/ul/cert.aspx?ULID=541348 | UL Yellow Card Link 3: https://iq.ul.com/ul/cert.aspx?ULID=220939
Heat deflection temperature, 0.45 MPa
HDT0.45,MPa136 °C
ISO 75/Be | Edgew 120*10*4 sp=100mm
Heat deflection temperature, 1.80 MPa
HDT1.8,MPa125 °C
ISO 75/Ae | Edgew 120*10*4 sp=100mm
Relative temperature index, electrical
RTIel130 °C
UL 746B
Relative temperature index, mechanical impact
RTIimp130 °C
UL 746B
Relative temperature index, mechanical strength
RTIstr130 °C
UL 746B
Specific heat capacity
cp1.25E-3 J/(kg·K) at 23 °C
ASTM C 351
Thermal conductivity
λ0.2 W/(m·K) at 23 °C
ISO 8302
Vicat softening temperature
Tsoft141 °C
ISO 306 | Rate B/50
Comparative tracking index
CTI3 V at 23 °C
UL 746A | (UL) {PLC}
Dielectric constant, 1MHz
εr,1MHz2.96 [-] at 23 °C
ASTM D 150
Dielectric constant, 60Hz
εr,60Hz3.17 [-] at 23 °C
ASTM D 150 | 50/60 Hz
Dielectric strength
EDS14.9 kV/mm at 23 °C
ASTM D 149 | in air, 3.2 mm
Dissipation factor, 1MHz
ε''1MHz0.01 [-] at 23 °C
ASTM D 150 |
Dissipation factor, 50Hz
ε''50Hz9E-4 [-] at 23 °C
ASTM D 150 | 50/60 Hz
High Amp Arc Ignition
HAI1.5 mm at 23 °C
UL 746A | PLC 0
High Volt Arc Track Rate
HVTR2 PLC Code at 23 °C
UL 746A | (PLC)
Hot-Wire Ignition
HWI1.1 mm at 23 °C
UL 746A | PLC 3
Volume resistivity
ρel, vol1.00E+17 Ω·cm at 23 °C
ASTM D 257
Haze
H1 %
ASTM D 1003 | 2.54 mm
Refractive index
nd1.59 [-]
ASTM D542
Transmission
t88 %
ASTM D 1003 | 2.54 mm
Melt mass-flow rate
MFR10.5 g/10min
ASTM D 1238 | 300°C/1.2 kgf
Melt volume-flow rate
MVR11 cm³/10min
ISO 1133 | MVR at 300°C/1.2 kg
Shrinkage
cshrink0.3 % at 23 °C
SABIC method | 3.2 mm
Application areas
Enclosure/Housing/Cover, Individual Equiptment, Forward Lighting, Building Accessory, Cluster, Data Transfer, Document Handling, LED Lighting, Rear/Signal Lighting, Wireless Communications, Irrigation
Availability
Europe,Asia,Americas
Features
Aesthetics & Visual effects
Processing methods
Drying Temperature: 120 °C | Drying Time: 2 to 4.0 hrs | Drying Time (Cumulative): 48 hrs | Maximum Moisture Content: 0.02 % | Melt Temperature: 280 to 315.0 °C | Nozzle Temperature: 270 to 310.0 °C | Front - Zone 3 Temperature: 280 to 315.0 °C | Middle - Zone 2 Temperature: 270 to 305.0 °C | Rear - Zone 1 Temperature: 270 to 295.0 °C | Mold Temperature: 70 to 110.0 °C | Back Pressure: 0.3 to 0.7 MPa | Screw Speed: 40 to 70.0 rpm | Shot to Cylinder Size: 40 to 60.0 % | Vent Depth: 0.025 to 0.076 mm
Supplier Disclaimer
While the information is provided in good faith, SABIC MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Buyer must determine the suitability of SABIC's materials for the Buyer's particular use through appropriate testing and analysis. No statement by SABIC concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right.
This material data has been provided by Sabic.