LNP* THERMOCOMP* WF006XXP is a compound based on PBT resin containing 30% glass. Added features of this grade include: excellent strength, stiffness and dimensional stability, high heat resistance. Good for appliance handles, spotlights, electric motors, connectors.
See where LNP™ THERMOCOMP™ Compound WF006XXP falls on the material property chart for Density against Elastic modulus in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.
Density
ρ1.53 g/cm³ at 23 °C
ASTM D 792
Limiting oxygen index
LOI19 % at 23 °C
Moisture absorption
cmoisture0.08 % at 23 °C
ISO 62 | (23°C / 50% RH)
Relative density
ρrel1.53 [-] at 23 °C
ASTM D 792 |
Specific volume
v0.65 cm³/g at 23 °C
ASTM D 792
Water absorption
cwater0.06 % at 23 °C
ASTM D 570 | (23°C/24hrs)
Ball Pressure Test
Passs
Coefficient of thermal expansion
α2.52E-5 1/K at 23 °C
ISO 11359-2 | -40°C to 40°C
Coefficient of thermal expansion, transverse
αtrans1.2E-4 1/K at 23 °C
ISO 11359-2 | -40°C to 40°C
Flammability
UL Yellow Card Link: https://iq.ul.com/ul/cert.aspx?ULID=103952715 | UL Recognized, 94HB Flame Class Rating: 0.84 mm UL 94 | Glow Wire Ignitability Temperature, 1.0 mm: 775 °C IEC 60695-2-13 | Glow Wire Ignitability Temperature, 1.5 mm: 775 °C IEC 60695-2-13 | Glow Wire Flammability Index, 1.0 mm: 750 °C IEC 60695-2-12 | Glow Wire Flammability Index, 1.5 mm: 750 °C IEC 60695-2-12 | UL Yellow Card Link 2: https://iq.ul.com/ul/cert.aspx?ULID=103938351
Glow Wire Ignition Temperature
GWIT825 °C
IEC 60695-2-13 | 3.0 mm
Heat deflection temperature, 0.45 MPa
HDT0.45,MPa217 °C
ISO 75/Bf | Flatw 80*10*4 sp=64mm
Heat deflection temperature, 1.80 MPa
HDT1.8,MPa204 °C
ISO 75/Af | Flatw 80*10*4 sp=64mm
Relative temperature index, electrical
RTIel140 °C
UL 746B
Relative temperature index, mechanical impact
RTIimp140 °C
UL 746B
Relative temperature index, mechanical strength
RTIstr140 °C
UL 746B
Thermal conductivity
λ0.19 W/(m·K) at 23 °C
ISO 8302
Vicat softening temperature
Tsoft223 °C
ISO 306 | Rate A/50
Comparative tracking index
CTI0 V at 23 °C
UL 746A | (UL) {PLC}
Dielectric constant, 100Hz
εr,100Hz3.8 [-] at 23 °C
ASTM D 150
Dielectric constant, 1MHz
εr,1MHz3.1 [-] at 23 °C
IEC 60250
Dielectric constant, 60Hz
εr,60Hz3.1 [-] at 23 °C
IEC 60250 | 50/60 Hz
Dielectric strength
EDS28 kV/mm at 23 °C
IEC 60243-1 | in oil, 0.8 mm
Dissipation factor, 100Hz
ε''100Hz1E-3 [-] at 23 °C
IEC 60250
Dissipation factor, 1MHz
ε''1MHz0.01 [-] at 23 °C
IEC 60250
Dissipation factor, 50Hz
ε''50Hz1E-3 [-] at 23 °C
IEC 60250 | 50/60 Hz
High Amp Arc Ignition
HAI0.38 mm at 23 °C
UL 746A | PLC 2
High Volt Arc Track Rate
HVTR1 PLC Code at 23 °C
UL 746A | (PLC)
Hot-Wire Ignition
HWI0.38 mm at 23 °C
UL 746A | PLC 4
Sheet resistivity, ROA
ρel,sheet, ROA1.00E+15 Ω at 23 °C
IEC 60093
Volume resistivity
ρel, vol1.00E+15 Ω·cm at 23 °C
IEC 60093 |
Melt mass-flow rate
MFR17 g/10min
ISO 1133 | 250°C/2.16 kg
Melt volume-flow rate
MVR13 cm³/10min
ISO 1133 | MVR at 250°C/2.16 kg
Shrinkage
cshrink0.5 % at 23 °C
Shrinkage, transverse
cshrink, trans0.5 % at 23 °C
SABIC method | 3.2 mm
Application areas
Electronic Components
Availability
Europe,Asia,Americas
Features
High Strength, High Heat Resistance, Good dimensional stability
Processing methods
Drying Temperature: 120 °C | Drying Time: 3 to 4.0 hrs | Drying Time (Cumulative): 12 hrs | Maximum Moisture Content: 0.02 % | Melt Temperature: 250 to 265.0 °C | Nozzle Temperature: 245 to 260.0 °C | Front - Zone 3 Temperature: 250 to 265.0 °C | Middle - Zone 2 Temperature: 245 to 260.0 °C | Rear - Zone 1 Temperature: 240 to 255.0 °C | Mold Temperature: 65 to 90.0 °C | Back Pressure: 0.3 to 0.7 MPa | Screw Speed: 50 to 80.0 rpm | Shot to Cylinder Size: 40 to 80.0 % | Vent Depth: 0.025 to 0.038 mm
Supplier Disclaimer
While the information is provided in good faith, SABIC MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Buyer must determine the suitability of SABIC's materials for the Buyer's particular use through appropriate testing and analysis. No statement by SABIC concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right.
This material data has been provided by Sabic.