LNP™ COLORCOMP™ D1000RF is an unfilled compound based on Polycarbonate resin. Added features of this grade include: Non-Halogenated, Mold Release, UL Rated HB. Good for small, intricate parts.
Density
ρ1.19 g/cm³ at 23 °C
ASTM D 792
Relative density
ρrel1.2 [-] at 23 °C
ASTM D 792
Specific volume
v0.83 cm³/g at 23 °C
ASTM D 792
Water absorption
cwater0.58 % at 23 °C
ASTM D 570 | equilibrium, 100°C
Impact strength, Charpy unnotched Iunnot
ISO 179/1eU | Unnotch Edgew 80*10*3 sp=62mm, -30°C
Impact strength, Izod unnotched IIzod,unnot
ISO 180/1U | 80*10*3, 23°C
Coefficient of thermal expansion
α6.84E-5 1/K at 23 °C
ASTM E 831 | -40°C to 95°C
Flammability
UL Yellow Card Link: https://iq.ul.com/ul/cert.aspx?ULID=103951133 | UL Recognized, 94HB Flame Class Rating: 0.7 mm UL 94 | Radiant Panel Listing: TRUE - UL Tested | UV-light, water exposure/immersion: F2 - UL 746C
Heat deflection temperature, 0.45 MPa
HDT0.45,MPa137 °C
ASTM D 648 | 6.4 mm, unannealed
Heat deflection temperature, 1.80 MPa
HDT1.8,MPa129 °C
ASTM D 648 | 6.4 mm, unannealed
Relative temperature index, electrical
RTIel130 °C
UL 746B
Relative temperature index, mechanical impact
RTIimp130 °C
UL 746B
Relative temperature index, mechanical strength
RTIstr130 °C
UL 746B
Specific heat capacity
cp1.25E-3 J/(kg·K) at 23 °C
ASTM C 351
Thermal conductivity
λ0.25 W/(m·K) at 23 °C
ASTM C177
Vicat softening temperature
Tsoft154 °C
ASTM D 1525 | Rate B/50
Comparative tracking index
CTI2 V at 23 °C
UL 746A | (UL) {PLC}
Dielectric constant, 1MHz
εr,1MHz2.96 [-] at 23 °C
ASTM D 150
Dielectric constant, 60Hz
εr,60Hz3.17 [-] at 23 °C
ASTM D 150 | 50/60 Hz
Dielectric strength
EDS14.9 kV/mm at 23 °C
ASTM D 149 | in air, 3.2 mm
Dissipation factor, 1MHz
ε''1MHz0.01 [-] at 23 °C
ASTM D 150
Dissipation factor, 50Hz
ε''50Hz9E-4 [-] at 23 °C
ASTM D 150 | 50/60 Hz
High Amp Arc Ignition
HAI1.5 mm at 23 °C
UL 746A | PLC 0
High Volt Arc Track Rate
HVTR4 PLC Code at 23 °C
UL 746A | (PLC)
Hot-Wire Ignition
HWI1.1 mm at 23 °C
UL 746A | PLC 3
Volume resistivity
ρel, vol1.00E+17 Ω·cm at 23 °C
ASTM D 257
Haze
H1 %
ASTM D 1003 | 2.54 mm
Refractive index
nd1.59 [-]
ASTM D542
Transmission
t88 %
ASTM D 1003 | 2.54 mm
Melt mass-flow rate
MFR17.5 g/10min
ASTM D 1238 | 300°C/1.2 kgf
Shrinkage
cshrink0.5 % at 23 °C
SABIC method | 3.2 mm
Application areas
Electronic Components
Availability
Europe,Asia,Americas
Features
Custom Color, Appearance & Durability
Processing methods
Drying Temperature: 120 °C | Drying Time: 3 to 4.0 hrs | Drying Time (Cumulative): 48 hrs | Maximum Moisture Content: 0.02 % | Melt Temperature: 280 to 305.0 °C | Nozzle Temperature: 275 to 300.0 °C | Front - Zone 3 Temperature: 280 to 305.0 °C | Middle - Zone 2 Temperature: 270 to 295.0 °C | Rear - Zone 1 Temperature: 260 to 280.0 °C | Mold Temperature: 70 to 95.0 °C | Back Pressure: 0.3 to 0.7 MPa | Screw Speed: 40 to 70.0 rpm | Shot to Cylinder Size: 40 to 60.0 % | Vent Depth: 0.025 to 0.076 mm
Supplier Disclaimer
While the information is provided in good faith, SABIC MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Buyer must determine the suitability of SABIC's materials for the Buyer's particular use through appropriate testing and analysis. No statement by SABIC concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right.
This material data has been provided by Sabic.