30% Glass fiber filled, standard flow Polyetherimide (Tg 217C). ECO Conforming. US FDA Food Contact compliant in recognized colors.
See where ULTEM™ Resin 2300F - Americas falls on the material property chart for Density against Elastic modulus in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.
Density
ρ1.51 g/cm³ at 23 °C
ISO 1183
Limiting oxygen index
LOI50 % at 23 °C
Moisture absorption
cmoisture0.5 % at 23 °C
ISO 62 | (23°C / 50% RH)
Relative density
ρrel1.51 [-] at 23 °C
ASTM D 792 |
Water absorption
cwater0.9 % at 23 °C
ISO 62-1 | (23°C/saturated)
Ball Pressure Test
nan
Coefficient of thermal expansion
α2E-5 1/K at 23 °C
ISO 11359-2 | 23°C to 150°C
Coefficient of thermal expansion, transverse
αtrans6E-5 1/K at 23 °C
ISO 11359-2 | 23°C to 150°C
Flammability
UL Recognized, 94-5VA Flame Class Rating: 1.2 mm UL 94 | UL Recognized, 94V-0 Flame Class Rating: 0.25 mm UL 94 | UL Yellow Card Link: https://iq.ul.com/ul/cert.aspx?ULID=221099
Glow Wire Ignition Temperature
GWIT900 °C
IEC 60695-2-13 | 2.0 mm
Heat deflection temperature, 0.45 MPa
HDT0.45,MPa212 °C
ASTM D 648 | 6.4 mm, unannealed
Heat deflection temperature, 1.80 MPa
HDT1.8,MPa210 °C
ISO 75/Ae | Edgew 120*10*4 sp=100mm
Relative temperature index, electrical
RTIel180 °C
UL 746B
Relative temperature index, mechanical impact
RTIimp170 °C
UL 746B
Relative temperature index, mechanical strength
RTIstr180 °C
UL 746B
Thermal conductivity
λ0.29 W/(m·K) at 23 °C
ISO 8302
Vicat softening temperature
Tsoft220 °C
ISO 306 | Rate B/120
Comparative tracking index
CTI4 V at 23 °C
UL 746A | (UL) {PLC}
Dielectric constant, 1MHz
εr,1MHz3.4 [-] at 23 °C
IEC 60250
Dielectric constant, 60Hz
εr,60Hz3.3 [-] at 23 °C
IEC 60250 | 50/60 Hz
Dielectric strength
EDS24.8 kV/mm at 23 °C
ASTM D 149 | in air, 1.6 mm
Dissipation factor
ε''5.3E-3 [-] at 23 °C
ASTM D 150 | 2450 MHz
Dissipation factor, 1MHz
ε''1MHz2.3E-3 [-] at 23 °C
IEC 60250
Dissipation factor, 1kHz
ε''1KHz1.5E-3 [-] at 23 °C
ASTM D 150
Dissipation factor, 50Hz
ε''50Hz1.6E-3 [-] at 23 °C
IEC 60250 | 50/60 Hz
High Amp Arc Ignition
HAI3 mm at 23 °C
UL 746A | PLC 4
High Volt Arc Track Rate
HVTR3 PLC Code at 23 °C
UL 746A | (PLC)
Hot-Wire Ignition
HWI3 mm at 23 °C
UL 746A | PLC 1
Sheet resistivity, ROA
ρel,sheet, ROA1.00E+15 Ω at 23 °C
IEC 60093
Volume resistivity
ρel, vol3.00E+16 Ω·cm at 23 °C
ASTM D 257
Melt mass-flow rate
MFR5 g/10min
ASTM D 1238 | 337°C/6.6 kgf
Melt volume-flow rate
MVR6 cm³/10min
ISO 1133 | MVR at 360°C/5.0 kg
Shrinkage
cshrink0.2 % at 23 °C
SABIC method | on tensile bar
Shrinkage, transverse
cshrink, trans0.2 % at 23 °C
SABIC method | 3.2 mm
Application areas
Non-LED Lighting, Aerospace, Electronic Components
Availability
Europe,Americas
Features
High Stiffness, Hydrolytic Stability, Chemical Resistance, Low Smoke and Toxicity, Good Mechanicals in Broad Temperature Range, Low Creep Sensitivity, Low Shrinkage, Good metal adhesion, Amorphous, High Strength, General Purpose, High Heat Resistance, Good dimensional stability, Flame Retardant, Food Contact Acceptable
Processing methods
Back Pressure: 0.3 to 0.7 MPa | Mold Temperature: 135 to 165.0 °C | Maximum Moisture Content: 0.02 % | Vent Depth: 0.025 to 0.076 mm | Nozzle Temperature: 345 to 400.0 °C | Drying Time (Cumulative): 24 hrs | Middle - Zone 2 Temperature: 340 to 400.0 °C | Rear - Zone 1 Temperature: 330 to 400.0 °C | Screw Speed: 40 to 70.0 rpm | Shot to Cylinder Size: 40 to 60.0 % | Melt Temperature: 350 to 400.0 °C | Drying Temperature: 150 °C | Drying Time: 4 to 6.0 hrs | Front - Zone 3 Temperature: 345 to 400.0 °C
Supplier Disclaimer
While the information is provided in good faith, SABIC MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Buyer must determine the suitability of SABIC's materials for the Buyer's particular use through appropriate testing and analysis. No statement by SABIC concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right.
This material data has been provided by Sabic.