General
Mechanical
Property | Temperature | Value | Comment |
---|---|---|---|
Elongation | 23.0 °C | 9 % Show Supplier Material materials with Elongation of 9 % | ASTM D 638 | yld, Type I, 50 mm/min |
Flexural modulus | 23.0 °C | 2.4 GPa Show Supplier Material materials with Flexural modulus of 2.4 GPa | ASTM D 790 | 2.6 mm/min, 100 mm span |
Flexural strength | 23.0 °C | 99 MPa Show Supplier Material materials with Flexural strength of 99 MPa | ASTM D 790 | yld, 2.6 mm/min, 100 mm span |
Impact strength, Izod notched | 23.0 °C | 176 kJ/m² Show Supplier Material materials with Impact strength, Izod notched of 176 kJ/m² | ASTM D 256 | notched, 23°C |
Impact strength, Izod notched, ASTM | 23.0 °C | 106 J/m Show Supplier Material materials with Impact strength, Izod notched, ASTM of 106 J/m | ASTM D 256 |
Instrumented Impact, at Peak | 23.0 °C | 40 J Show Supplier Material materials with Instrumented Impact, at Peak of 40 J | ASTM D 3763 | 23°C |
Tensile strength | 23.0 °C | 59 MPa Show Supplier Material materials with Tensile strength of 59 MPa | ASTM D 638 | brk, Type I, 50 mm/min |
Thermal
Property | Temperature | Value | Comment |
---|---|---|---|
Coefficient of thermal expansion | 23.0 °C | 9.54E-5 1/K Show Supplier Material materials with Coefficient of thermal expansion of 9.54E-5 1/K | ASTM E 831 | -20°C to 150°C |
Coefficient of thermal expansion, transverse | 23.0 °C | 8.1E-5 1/K Show Supplier Material materials with Coefficient of thermal expansion, transverse of 8.1E-5 1/K | ASTM E 831 | -20°C to 150°C |
Heat deflection temperature | 125 - 204 °C Show Supplier Material materials with Heat deflection temperature of 125 - 204 °C | ||
Heat deflection temperature, 0.45 MPa | 204 °C Show Supplier Material materials with Heat deflection temperature, 0.45 MPa of 204 °C | ASTM D 648 | 6.4 mm, unannealed | |
Heat deflection temperature, 1.80 MPa | 125 °C Show Supplier Material materials with Heat deflection temperature, 1.80 MPa of 125 °C | ASTM D 648 | 6.4 mm, unannealed | |
Vicat softening temperature | 245 °C Show Supplier Material materials with Vicat softening temperature of 245 °C | ASTM D 1525 | Rate B/50 |
Electrical
Property | Temperature | Value | Comment |
---|---|---|---|
Dielectric constant, 1MHz | 23.0 °C | 2.76 [-] Show Supplier Material materials with Dielectric constant, 1MHz of 2.76 [-] | ASTM D 150 |
Dielectric constant, 60Hz | 23.0 °C | 3.27 [-] Show Supplier Material materials with Dielectric constant, 60Hz of 3.27 [-] | ASTM D 150 | 50/60 Hz |
Dielectric strength | 23.0 °C | 25.5 kV/mm Show Supplier Material materials with Dielectric strength of 25.5 kV/mm | ASTM D 149 | in oil, 3.2 mm |
Dissipation factor, 1MHz | 23.0 °C | 0.02 [-] Show Supplier Material materials with Dissipation factor, 1MHz of 0.02 [-] | ASTM D 150 | |
Dissipation factor, 50Hz | 23.0 °C | 0.04 [-] Show Supplier Material materials with Dissipation factor, 50Hz of 0.04 [-] | ASTM D 150 | 50/60 Hz |
Sheet resistivity, ROA | 23.0 °C | 1.70E+16 Ω Show Supplier Material materials with Sheet resistivity, ROA of 1.70E+16 Ω | ASTM D 257 |
Volume resistivity | 23.0 °C | 4.40E+16 Ω·cm Show Supplier Material materials with Volume resistivity of 4.40E+16 Ω·cm | ASTM D 257 |
Rheological Properties
Property | Temperature | Value | Comment |
---|---|---|---|
Shrinkage | 23.0 °C | 1.3 % Show Supplier Material materials with Shrinkage of 1.3 % | SABIC method | 3.2 mm |
Technological properties
Property | ||
---|---|---|
Application areas | Wheel Cover, Plumbing, Door Handle, Enclosures | |
Availability | Asia | |
Processing methods | Rear - Zone 1 Temperature: 255 to 295.0°C | |
Supplier Disclaimer | While the information is provided in good faith, SABIC MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Buyer must determine the suitability of SABIC's materials for the Buyer's particular use through appropriate testing and analysis. No statement by SABIC concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right. |