Dianhydrides & Imides 1040A - Americas

Want to keep this datasheet? Save it now in your required format

Description

Transparent, high flow polyetherimide.

This material data has been provided by Sabic.

All metrics apply to room temperature unless otherwise stated. SI units used unless otherwise stated.
Equivalent standards are similar to one or more standards provided by the supplier. Some equivalent standards may be stricter whereas others may be outside the bounds of the original standard.

Ashby charts

Properties

General

PropertyTemperatureValueComment

Relative density

23.0 °C

1.27 [-]

Show Supplier Material materials with Relative density of 1.27 [-]

ASTM D 792 |

Mechanical

PropertyTemperatureValueComment

Elastic modulus

23.0 °C

3.44 GPa

Show Supplier Material materials with Elastic modulus of 3.44 GPa

ASTM D 638 | 5 mm/min

Elongation

23.0 °C

10 %

Show Supplier Material materials with Elongation of 10 %

ASTM D 638 | brk, Type I, 5 mm/min

Flexural modulus

23.0 °C

3.51 GPa

Show Supplier Material materials with Flexural modulus of 3.51 GPa

ASTM D 790 | 2.6 mm/min, 100 mm span

Flexural strength

23.0 °C

159 MPa

Show Supplier Material materials with Flexural strength of 159 MPa

ASTM D 790 | yld, 2.6 mm/min, 100 mm span

Impact strength, Izod notched

23.0 °C

21 kJ/m²

Show Supplier Material materials with Impact strength, Izod notched of 21 kJ/m²

ASTM D 256 | notched, 23°C

Impact strength, Izod notched, ASTM

23.0 °C

21 J/m

Show Supplier Material materials with Impact strength, Izod notched, ASTM of 21 J/m

ASTM D 256 | notched, 23°C

Impact strength, Izod unnotched, ASTM

23.0 °C

470 J/m

Show Supplier Material materials with Impact strength, Izod unnotched, ASTM of 470 J/m

ASTM D 4812 | 23°C

Tensile strength

23.0 °C

97 MPa

Show Supplier Material materials with Tensile strength of 97 MPa

ASTM D 638 | yld, Type I, 5 mm/min

Thermal

PropertyValueComment

Heat deflection temperature

196 °C

Show Supplier Material materials with Heat deflection temperature of 196 °C

Heat deflection temperature, 1.80 MPa

196 °C

Show Supplier Material materials with Heat deflection temperature, 1.80 MPa of 196 °C

ASTM D 648 | 6.4 mm, unannealed

Rheological Properties

PropertyTemperatureValueComment

Melt mass-flow rate

6.6 g/10min

Show Supplier Material materials with Melt mass-flow rate of 6.6 g/10min

ASTM D 1238 | 295°C/6.6 kgf

Shrinkage

23.0 °C

0.5 %

Show Supplier Material materials with Shrinkage of 0.5 %

SABIC method | 3.2 mm

Technological properties

Property
Application areas

Enclosures, Water Treatment/Filtration, Wire & cable, Adhesives

Availability

Americas

Supplier Disclaimer

While the information is provided in good faith, SABIC MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Buyer must determine the suitability of SABIC's materials for the Buyer's particular use through appropriate testing and analysis. No statement by SABIC concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right.