UGI® HT286 Annealed

Want to keep this datasheet? Save it now in your required format

Description

UGI® HT286 is an austenitic iron-base alloy containing nickel, chromium, molybdenum and titanium. The titanium and small amount of aluminium it contains enables the alloy to be strengthened by precipitation of the Ni3 (Ti,Al) gamma prime phase, providing good mechanical properties from cryogenic temperatures up to 700°C.

Related Standards

Equivalent Materials

This material data has been provided by Ugitech SA.

All metrics apply to room temperature unless otherwise stated. SI units used unless otherwise stated.
Equivalent standards are similar to one or more standards provided by the supplier. Some equivalent standards may be stricter whereas others may be outside the bounds of the original standard.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

Properties

General

PropertyTemperatureValue

Density

23.0 °C

8 g/cm³

Show Supplier Material materials with Density of 8 g/cm³

Mechanical

PropertyTemperatureValueComment

Elastic modulus

23.0 °C

195 GPa

Show Supplier Material materials with Elastic modulus of 195 GPa

Tensile strength

23.0 °C

650 MPa

Show Supplier Material materials with Tensile strength of 650 MPa

max.

Thermal

PropertyTemperatureValueComment

Coefficient of thermal expansion

100.0 °C

1.65E-5 1/K

Show Supplier Material materials with Coefficient of thermal expansion of 1.65E-5 1/K

for 20 to mentioned temperature

Melting point

1370 - 1400 °C

Show Supplier Material materials with Melting point of 1370 - 1400 °C

Thermal conductivity

23.0 °C

14 W/(m·K)

Show Supplier Material materials with Thermal conductivity of 14 W/(m·K)

Electrical

PropertyTemperatureValue

Electrical resistivity

23.0 °C

9.1E-7 Ω·m

Show Supplier Material materials with Electrical resistivity of 9.1E-7 Ω·m

Chemical properties

PropertyValueComment

Aluminium

0.35 %

Show Supplier Material materials with Aluminium of 0.35 %

max.

Boron

0.03 - 0.1 %

Show Supplier Material materials with Boron of 0.03 - 0.1 %

Carbon

0.08 %

Show Supplier Material materials with Carbon of 0.08 %

max.

Chromium

13.5 - 16 %

Show Supplier Material materials with Chromium of 13.5 - 16 %

Iron

Balance

Manganese

1 - 2 %

Show Supplier Material materials with Manganese of 1 - 2 %

Molybdenum

1 - 1.5 %

Show Supplier Material materials with Molybdenum of 1 - 1.5 %

Nickel

24 - 27 %

Show Supplier Material materials with Nickel of 24 - 27 %

Phosphorus

0.03 %

Show Supplier Material materials with Phosphorus of 0.03 %

max.

Silicon

1 %

Show Supplier Material materials with Silicon of 1 %

max.

Sulfur

0.015 %

Show Supplier Material materials with Sulfur of 0.015 %

min.

Titanium

1.9 - 2.3 %

Show Supplier Material materials with Titanium of 1.9 - 2.3 %

Vanadium

0.1 - 0.5 %

Show Supplier Material materials with Vanadium of 0.1 - 0.5 %

Technological properties

Property
Application areas

  • Fasteners (screws, bolts, studs) for high-temperature environments in the aerospace and automotive industries
  • Springs
  • Non-magnetic cryogenic parts
  • Blades

  • Corrosion properties

    UGI® HT286 has an oxidation resistance comparable to that of type AISI 310 stainless steel, up to 800°C. The corrosion resistance of this alloy is excellent up to 700°C in many atmospheres encountered in jet engine services. Its good resistance to high-temperature oxidation and intergranular corrosion, together with its absence of cobalt, non-magnetic structure and a higher yield strength than conventional stainless steel, have led to widespread use of UGI® HT286 for fasteners in the aerospace, nuclear, automotive and chemical engineering industries.


    EnvironmentBehaviour
    Sea waterModerate
    HumidityExcellent
    Sour oil/gasModerate
    Salt spray (NaCl)Good


    Test environment
    Boiling solution
    Corrosion rate in mm/year
    AISI 304UGI® HT286
    20%w acetic acid< 0.01< 0.01
    45%w formic acid1.20.2
    10%w oxalic acid1.20.4
    1%w hydrochloric acid2.72.1
    10%w sulphuric acid>120.75
    20%w phosphoric acid<0.010.35
    10%w sodium bisulfate1.60.2

    General machinability

    UGI® HT286 is more difficult to machine than standard stainless steels, mainly because of the very low sulphur content required to guarantee that this grade has a good hot workability. Without sulphide content, during machining UGI® HT286 produces long chips that are difficult to manage, especially in drilling operations.

    Because of its high mechanical characteristics in the aged condition (even at the temperatures reached in the vicinity of the cutting tool), UGI® HT286 is often machined in its annealed condition. But, in this condition, sticking and edge build-up phenomena on the tools used results in poor tool life and a very bad surface finish. It can therefore be advisable to increase the mechanical characteristics of the material in its annealed condition through cold working or through an ‘ageing’ heat treatment prior to machining. Compared to other superalloys, relatively high speeds can be used to machine UGI® HT286. During machining, this grade is subject to work hardening, inducing tough chips but also a harder machined surface than the original material. This results in notching and chipping during subsequent machining passes. Sharper, more positive cutting edges reduce this phenomenon and are therefore preferred. Generally CVD (chemical vapor deposition) coatings are preferred for improved speed capability and longer tool life.

    Heat Treatment

    Solution annealing: 1 hour at 980°C, followed by water cooling

  • This solution-annealing treatment regenerates and softens the structure after cold working (i.e. cold heading, drawing, etc.).

  • Other

    Available products:


    ProductFormFinishToleranceDimensions
    BarsRoundAs drawn or groundh7 min1-15
    RoundTurned and polishedh10-h112-70 mm
    Drawn wireRoundDrawn (1)0.8-18 mm
    ProfileBright2-70 mm²


    (1)With or without soap coating


    Other products: contact the supplier