Show Supplier Material materials with Density of 7.7 g/cm³
Show Supplier Material materials with Elastic modulus of 200 GPa
Show Supplier Material materials with Elastic modulus of 195 GPa
Show Supplier Material materials with Elastic modulus of 185 GPa
Show Supplier Material materials with Elastic modulus of 175 GPa
Show Supplier Material materials with Elastic modulus of 170 GPa
Show Supplier Material materials with Elongation of 12.0 %
Show Supplier Material materials with Elongation of 16 %
269.0 - 331.0 [-]
Show Supplier Material materials with Hardness, Brinell of 269.0 - 331.0 [-]
Coefficient of thermal expansion
Show Supplier Material materials with Coefficient of thermal expansion of 0.0000103 1/K
20 to 100°C
Show Supplier Material materials with Coefficient of thermal expansion of 0.0000108 1/K
20 to 200°C
Show Supplier Material materials with Coefficient of thermal expansion of 0.0000112 1/K
20 to 300°C
Show Supplier Material materials with Coefficient of thermal expansion of 0.0000116 1/K
20 to 400°C
Specific heat capacity
Show Supplier Material materials with Specific heat capacity of 430 J/(kg·K)
Show Supplier Material materials with Thermal conductivity of 15 W/(m·K)
Show Supplier Material materials with Electrical resistivity of 8e-07 Ω·m
Show Supplier Material materials with Carbon of 0.06
15.0 - 17.0 %
Show Supplier Material materials with Chromium of 15.0 - 17.0 %
Show Supplier Material materials with Copper of 0.5
Show Supplier Material materials with Manganese of 1.5
0.8 - 1.2 %
Show Supplier Material materials with Molybdenum of 0.8 - 1.2 %
4.0 - 5.0 %
Show Supplier Material materials with Nickel of 4.0 - 5.0 %
Show Supplier Material materials with Nitrogen of 0.02 %
Show Supplier Material materials with Phosphorus of 0.03
Show Supplier Material materials with Silicon of 0.6000000000000001
Show Supplier Material materials with Sulfur of 0.005
UGI 4418 AIR can be cold formed by conventional cold-working processes (bar drawing, wire drawing, forming, profiling, etc.). Its high mechanical properties require particular attention. After or during cold-forming operations, quenching may be necessary to soften the grade. In the event of high levels of deformation, a complete quenching and tempering process is recommended.
Due to its high percentage of nickel, chromium and molybdenum and its low carbon content, UGI 4418 AIR has good corrosion resistance.
Pitting corrosion: The pitting potentials were measured as specified in ISO 15158-2014 in a solution containing 0.02M NaCl at 23°C. UGI 4418 AIR also has far better pitting corrosion resistance than a 13% Cr martensitic (type 1.4006). The results show that the pitting corrosion resistance of UGI 4418 AIR is similar to that of 1.4542 and 1.4307 (containing 0.020% of sulphur).
Intergranular corrosion: Its structure and composition make UGI 4418 AIR insensitive to intergranular corrosion.
UGI 4418 AIR is difficult to soften due to its chemical composition leading to a very low transformation point (Ac1). Soft annealing is generally carried out between 600 and 650°C.
UGI 4418 AIR quenching heat treatment consists of austenitizing between 1010°C and 1060°C, followed by oil quenching (or air quenching for smaller sections). To limit the risks of quenching cracks, tempering must be carried out as soon as possible after the quenching operation, after returning to the ambient temperature.
The tempering temperature must be adjusted according to the mechanical properties required.
The tempering period is generally between 2 h and 4 h and is followed by air or oil cooling. Double tempering can be used to soften the grade further. The temperature range between 400°C and 450°C should be avoided, as it can lead to excessive metal embrittlement (see chart on the right side of the material page).
Heating between 1150°C and 1200°C is recommended. Hot forming (forging) must preferably be carried out at a temperature of between 1200°C and 900°C, followed by air cooling. The behaviour of UGI 4418 AIR during forging is equivalent to that of a type 1.4301 austenitic grade. Full heat treatment, austenitizing/quenching followed by tempering, is recommended after hot forming.
Other products: contact the supplier
UGI 4418 AIR can be welded by electric arc (GMAW, GTAW, SMAW, etc.) and by most other processes (spot welding, seam welding, LASER, etc.). Due to its low percentage of carbon and its nickel content, UGI 4418 AIR is easier to weld than most martensitic stainless steels.
Low-carbon martensite combined with finely dispersed residual austenite gives the heat-affected zones (HAZ) of UGI 4418 AIR excellent toughness in the as-welded condition. UGI 4418 AIR is therefore only slightly susceptible to cold cracking after welding and it is not normally necessary to preheat the parts, unless the parts to be welded are very thick or their geometry is liable to generate high stress concentrations at the welds after cooling (in this case, preheating at 100-120°C is recommended).
If the Weld Metal (WM) does not require the mechanical properties of UGI 4418 AIR, an austenitic grade such as A316LM or A316LT can be used as filler metal. Post-weld heat treatment is then generally not necessary. Where the WM must have the same mechanical properties as those of UGI 4418 AIR, a homogeneous filler metal must be used (such as “16 5 1”). In this case, post weld heat treatment at 580-600°C is recommended.
For GMAW with homogeneous filler metal, a slightly oxidizing shielding gas such as Ar + 1-2% CO₂ will be chosen to avoid too high a percentage of oxygen in the WM, thus ensuring good impact properties for these WMs.