EN 573-3 Grade AW-5454 H16

Want to keep this datasheet? Save it now in your required format

Description

Material EN AW-Al Mg3Mn is produced for sheet metals, strip and plates, for HF-welded tubes, for extruded and drawn components. The material is food-safe and is used for forged parts and prematerial. To the comparable mark AlMg2,7Mn, material No. 3.3537 acc. to DIN 1725-1 : 1983-02 applies: At AlMg2,7 occurs a press effect to extrusion products that causes considerable strength increase in pressure direction. This is a result of Mn-addition as well as icrease of high-temperature strength. AlMg2,7Mn is due to its relativly favorable strength qualities usable or staticly loaded constructions The alloy has a high resistance to corrosion, seawater and salted atmosphere. Strength increases and cold workability decreases according to the Mg-content. It is naturally hard, i.e. a strength increase can only be achieved by cold forming, not by controlled heat treatment. Machinability and weldability are enhanced by increasing Mg-content. Application: in apparatus engineering for pressure tanks (cold carboretor, air breakdown), for low-temperatur tanks resp. for temperatures up to 250°C. In vehicle manufacturing for bulk and tank transporter, motor busses, coolings and air-conditioning systems, in construction trade for carrying constuctions and for heat insulation as well as in food industry for commercial devices.

Related Standards

Equivalent Materials

This material data has been provided by WIAM,AluKey.

All metrics apply to room temperature unless otherwise stated. SI units used unless otherwise stated.
Equivalent standards are similar to one or more standards provided by the supplier. Some equivalent standards may be stricter whereas others may be outside the bounds of the original standard.

Ashby charts

See where falls on the material property chart for against in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

All categories

Properties

General

Property	Value	Temperature
Density	2.68 - 2.69 g/cm³ Show Material materials with Density of 2.68 - 2.69 g/cm³ at 20.0 °C	20.0 °C
	2.68 g/cm³ Show Material materials with Density of 2.68 g/cm³ at 23.0 °C	23.0 °C

Mechanical

Property	Value	Temperature	Comment
Bending Fatigue Strength	140 MPa Show Material materials with Bending Fatigue Strength of 140 MPa at 23.0 °C	23.0 °C
Elastic modulus	70.5 GPa Show Material materials with Elastic modulus of 70.5 GPa at 20.0 °C	20.0 °C
	70.5 GPa Show Material materials with Elastic modulus of 70.5 GPa at 23.0 °C	23.0 °C
	Unlock all property charts
Elongation	4 % Show Material materials with Elongation of 4 % at 20.0 °C	20.0 °C
Elongation A100	4 % Show Material materials with Elongation A100 of 4 % at 23.0 °C	23.0 °C
Plane-Strain Fracture Toughnes	22 - 35 MPa·√m Show Material materials with Plane-Strain Fracture Toughnes of 22 - 35 MPa·√m at 23.0 °C	23.0 °C	Typical for Wrought 5000 Series Aluminium
Poisson's ratio	0.33 [-] Show Material materials with Poisson's ratio of 0.33 [-] at 20.0 °C	20.0 °C
Shear modulus	26.5 - 27 GPa Show Material materials with Shear modulus of 26.5 - 27 GPa at 20.0 °C	20.0 °C
	26.5 GPa Show Material materials with Shear modulus of 26.5 GPa at 23.0 °C	23.0 °C
	Unlock all property charts
Tensile strength	290 MPa Show Material materials with Tensile strength of 290 MPa at 20.0 °C	20.0 °C
	290 MPa Show Material materials with Tensile strength of 290 MPa at 23.0 °C	23.0 °C
	Unlock all property charts
Yield strength Rp0.2	260 MPa Show Material materials with Yield strength Rp0.2 of 260 MPa at 20.0 °C	20.0 °C
	260 MPa Show Material materials with Yield strength Rp0.2 of 260 MPa at 23.0 °C	23.0 °C
	Unlock all property charts

Thermal

Property	Value	Temperature	Comment
Coefficient of thermal expansion	2.19E-5 1/K Show Material materials with Coefficient of thermal expansion of 2.19E-5 1/K at -50.0 °C	-50.0 °C
	2.19E-5 - 2.56E-5 1/K Show Material materials with Coefficient of thermal expansion of 2.19E-5 - 2.56E-5 1/K at 20.0 °C	20.0 °C
	2.36E-5 - 2.37E-5 1/K Show Material materials with Coefficient of thermal expansion of 2.36E-5 - 2.37E-5 1/K at 100.0 °C	100.0 °C
	2.46E-5 1/K Show Material materials with Coefficient of thermal expansion of 2.46E-5 1/K at 200.0 °C	200.0 °C
	2.56E-5 1/K Show Material materials with Coefficient of thermal expansion of 2.56E-5 1/K at 300.0 °C	300.0 °C
	Unlock all property charts
Max service temperature	150 °C Show Material materials with Max service temperature of 150 °C		Typical for Wrought 5000 Series Aluminium
Melting point	602 - 646 °C Show Material materials with Melting point of 602 - 646 °C
Specific heat capacity	897 - 900 J/(kg·K) Show Material materials with Specific heat capacity of 897 - 900 J/(kg·K) at 20.0 °C	20.0 °C
	900 J/(kg·K) Show Material materials with Specific heat capacity of 900 J/(kg·K) at 23.0 °C	23.0 °C
	Unlock all property charts
Thermal conductivity	135 - 150 W/(m·K) Show Material materials with Thermal conductivity of 135 - 150 W/(m·K) at 20.0 °C	20.0 °C
	130 - 150 W/(m·K) Show Material materials with Thermal conductivity of 130 - 150 W/(m·K) at 23.0 °C	23.0 °C
	Unlock all property charts

Electrical

Property	Value	Temperature
Electrical conductivity	2.10E+7 S/m Show Material materials with Electrical conductivity of 2.10E+7 S/m at 20.0 °C	20.0 °C
	1.90E+7 - 2.10E+7 S/m Show Material materials with Electrical conductivity of 1.90E+7 - 2.10E+7 S/m at 23.0 °C	23.0 °C
	Unlock all property charts
Electrical resistivity	5.1E-8 Ω·m Show Material materials with Electrical resistivity of 5.1E-8 Ω·m at 20.0 °C	20.0 °C
	4.76E-8 - 5.26E-8 Ω·m Show Material materials with Electrical resistivity of 4.76E-8 - 5.26E-8 Ω·m at 23.0 °C	23.0 °C
	Unlock all property charts

Chemical properties

Property
Chromium	0.05 - 0.2 %
Copper	0.1 %
Iron	0.4 %
Magnesium	2.4 - 3 %
Manganese	0.5 - 1 %
Other		Be < 0.0003 for welding additives, each 0.05, total 0.15, Rest Al
Silicon	0.25 %
Titanium	0.2 %
Zinc	0.25 %

Technological properties

Property
Anodizing	decorative: sufficient, Protective: good
Brazing	hard brazing (with flux/ without flux): poor / sufficient, friction soldering: acceptable, soft brazing with flux: poor
Corrosion properties	Seawater: very good, weathering: very good
Workability	Bending / Spinning (cold): good / acceptable, Impact extrusion (cold): sufficient, Deep drawing / upsetting (Condition) good (O) / good (H12)