AA Standards Grade 5052 H38

Want to keep this datasheet? Save it now in your required format

Description

Related Standards

Equivalent Materials

Ashby charts

See where AA Standards Grade 5052 H38 falls on the material property chart for Density against Elastic modulus in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Sign up to get access to this premium feature for free.

Properties

General

Density

ρ

2.68 - 2.7 g/cm³ at 20 °C

Dimension

Dimensions

Dicke

Mechanical

Elastic modulus

E

70 GPa at 20 °C

Show 5000 Series materials with Elastic modulus of 70 GPa at 20 °C

Elongation

A

25 % at -195 °C

Show 5000 Series materials with Elongation of 25 % at -195 °C

Elongation in 50 mm

Hide chart

Elongation A100

A100

7 % at 20 °C

Show 5000 Series materials with Elongation A100 of 7 % at 20 °C

Elongation A50

A50

2 - 7 % at 20 °C

Show 5000 Series materials with Elongation A50 of 2 - 7 % at 20 °C

Fatigue strength

SNf

140 MPa at 20 °C

Show 5000 Series materials with Fatigue strength of 140 MPa at 20 °C

for 5x10⁸ cycles

Hardness, Brinell

HB

77 [-] at 20 °C

Show 5000 Series materials with Hardness, Brinell of 77 [-] at 20 °C

500 kg load, 10 mm ball

Plane-Strain Fracture Toughnes

KIC

22 - 35 MPa·√m at 20 °C

Show 5000 Series materials with Plane-Strain Fracture Toughnes of 22 - 35 MPa·√m at 20 °C

Typical for Wrought 5000 Series Aluminium

Poisson's ratio

ν

0.33 [-] at 20 °C

Show 5000 Series materials with Poisson's ratio of 0.33 [-] at 20 °C

Typical for Wrought 5000 Series Aluminium

Shear modulus

G

25.9 GPa at 20 °C

Show 5000 Series materials with Shear modulus of 25.9 GPa at 20 °C

Shear strength

τ

165 MPa at 20 °C

Show 5000 Series materials with Shear strength of 165 MPa at 20 °C

Tensile strength

Rm

415 MPa at -195 °C

Show 5000 Series materials with Tensile strength of 415 MPa at -195 °C

up to 10000 h at temperature, at 35 MPa/min to yield strength and then at strain rate of 5%/min to fracture

Unlock all property charts

Yield strength

YS

250 MPa at 20 °C

Show 5000 Series materials with Yield strength of 250 MPa at 20 °C

Yield strength Rp0.2

Rp0.2

303 MPa at -196 °C

Show 5000 Series materials with Yield strength Rp0.2 of 303 MPa at -196 °C

up to 10000 h at temperature, at 35 MPa/min to yield strength and then at strain rate of 5%/min to fracture

Unlock all property charts

Thermal

Coefficient of thermal expansion

α

2.38E-5 - 2.4E-5 1/K at 20 °C

Unlock all property charts

Max service temperature

Tmax

150 °C

Typical for Wrought 5000 Series Aluminium

Melting point

Tm

605 - 650 °C

Specific heat capacity

cp

900 J/(kg·K) at 20 °C

Thermal conductivity

λ

138 - 140 W/(m·K) at 20 °C

Electrical

Electrical conductivity

σel

2.00E+7 - 2.03E+8 S/m at 20 °C

Unstated/Typical value

Electrical resistivity

ρel

5E-8 Ω·m at 20 °C

Specific Electrical conductivity

35 % IACS

Unstated value

Chemical properties

Element

Weight %

Comment

Al

95.8 - 97.7 %

Mg

2.2 - 2.8 %

Cr

0.15 - 0.35 %

Cu

0 - 0.1 %

Fe

0 - 0.4 %

More

Technological properties

Brazing

general: limited brazing

Corrosion properties

Stress corrosion cracking: no damage during operation and laboratory tests, general: very good, without protection in industrial or seawater atmosphere

General machinability

General: poor (O, H32), sufficient (H34, H36, H38)

Workability

general (condition): good (O), acceptable (H32, H34), poor(H36, H38)

This material data has been provided by MakeItFrom.com,ASM Handbook Volume 2 Properties and Selection: Nonferrous Alloys and Special-Purpose Materials,AluKey.

All metrics apply to room temperature unless otherwise stated. SI units used unless otherwise stated.
Equivalent standards are similar to one or more standards provided by the supplier. Some equivalent standards may be stricter whereas others may be outside the bounds of the original standard.